Nickel alloy bolts full threaded hex bolt

The high molybdenum content imparts resistance to localized corrosion such as pitting.

Hex bolts are used to fasten two or more parts together to form an assembly either because it cannot be manufactured as a single part or to allow for maintenance and repair disassembly. By definition “A Bolt is a headed and externally threaded mechanical device designed for insertion through holes in assembled parts to mate with a nut and is normally intended to be tightened or released by turning that nut.” When used with a preformed internally threaded (tapped) hole, the hex bolt’s head is turned to tighten, which technically makes it a screw (see our Tech Data section for a discussion regarding the differences between bolts and screws). Hex bolts are also known as: hex head bolts, cap screws, hex cap screws, hex head cap screws, machine bolts, hex machine bolts, hex head machine bolts and, if fully threaded, tap bolts, hex tap bolts and hex head tap bolts. A hex bolt is often differentiated from a hex cap screw by its underhead bearing surface: if it has a circular boss, called a washer face, it’s a hex cap screw¡ªif it doesn’t then it’s a hex bolt.

A finished hex nut, also known as a standard hex nut, has a smaller width across the flats and corners compared to a heavy hex nut. Heavy hex nuts are thicker and heavier in weight. The proof load strength is higher than a standard hex nut. Heavy hex nuts provide increased bearing surface area over finished nuts.

The reason ASTM B637 UNS N07718 bolts are ideally chosen for the manufacture of turbine engines. Since a turbine engine operates on basic thermodynamic principles, the efficiency of a turbine engine increases as the turbine inlet temperature increases.

Nimonic 80A washers are made from a precipitation hardenable nickel and chromium alloy with the addition of aluminum and titanium. This is manufactured by sourcing the raw material of Nimonic 80A alloy (also known as Alloy 80A). The gasket has good corrosion and oxidation resistance. It is also known for its high tensile strength. Not only does it have creep rupture properties up to 1500¡ãF, that means 815¡ãC. Available in hot forging, cold forging and bar stock forms suitable for working conditions. This is available in a variety of sizes so it can be preferred based on requirements.

Alloy K500 studs are threaded rods with threads on both ends. They can be of different types depending on thread distance from center and thread type. The material is resistant to high temperature and high pressure. It has a melting point of 1350 degrees Celsius, a minimum yield strength of 790MPa and a minimum tensile strength of 1100MPa. These values are twice as strong as level 304.

An Inconel 718 Fastener is a hardware device that joins or holds materials together, usually as a non-permanent connection. Joints can be non-permanent or permanent; the joined tool can be easily detached without damaging the previous joint, if the latter joint is damaged or reduced in strength.

It is used in chemical processing, pollution control, pulp and paper production, industrial and municipal waste treatment and the recovery of ¡°sour¡± natural gas.

ASTM B637 UNS N07718 is a nickel-chromium-molybdenum alloy designed to eliminate a wide range of severe corrosion conditions, pitting and crevice corrosion. It also exhibits extremely high tensile, yield and creep rupture properties at elevated temperatures. It is suitable for long-term use from low temperatures to 1200¡ãF. One of the defining features of the composition of B637 UNS N07718 is the addition of niobium to allow age hardening, which facilitates welding and annealing without unforced hardening during heating and cooling.

Hastelloy B-3 is a nickel-molybdenum alloy with excellent resistance to pitting, corrosion and stress corrosion cracking and better thermal stability than alloy B-2. Hastelloy UNS N10675 fasteners are suitable for aircraft, furnace and chemical process components, honeycomb and gas turbine combustion section components.

Hastelloy C22 fasteners are a general-purpose grade composed of chromium, nickel, molybdenum and tungsten alloys. These designs are designed to increase resistance to pitting, stress corrosion cracking (SSC) and crevice corrosion cracking. Alloy C-22 has excellent resistance to a variety of chemical process environments, including strong oxidizing agents such as ferric and cupric chlorides, chlorine, hot fouling solutions (organic and inorganic), formic and acetic acid, acetic anhydride, and seawater and Brine solution. C-22 alloy resists the formation of grain boundary precipitates in the weld heat affected zone and is therefore suitable for most chemical process applications in as-welded conditions.

Another feature of HASTELLOY-X fasteners is their excellent forming and welding characteristics. It can be forged and can be cold worked due to its good ductility. Common applications for Hastelloy x include use in aircraft furnaces and chemical process components.

Inconel 601 fasteners are designed to withstand severe corrosion and high temperature exposure. These fasteners contain nickel and chromium alloys for excellent corrosion, heat and oxidation resistance. Nickel content retains ductility and high temperature strength after prolonged use. Fasteners of this grade produce a tightly adherent scale that resists spalling under severe thermal cycling conditions.

At elevated temperatures the annealed and solution annealed alloy shows good resistance to scaling and has high strength. The alloy also resists ammonia bearing atmospheres, as well as nitrogen and carburizing gases.

C22 nickel alloy fasteners offer better overall corrosion resistance than its sister alloy Hastelloy C-276, and more specifically, it offers better protection when used in certain saturated wet chlorine environments. Additionally, its high chromium content provides C22 fasteners with better resistance to oxidative media than C276. This makes it excellent resistance to chloride-induced pitting, although in most cases C-276 fasteners are a more cost-effective option due to their availability, especially in sizes smaller than 1/ 2″ case.

Hastelloy C22 fasteners are a general-purpose grade composed of chromium, nickel, molybdenum and tungsten alloys. These designs are designed to increase resistance to pitting, stress corrosion cracking (SSC) and crevice corrosion cracking. It has high chromium content and good resistance to oxidizing media. Durable and strong, these fasteners can be used in a variety of applications. Fasteners are provided according to the needs of customers, who can obtain fasteners from us in custom lengths and thicknesses. All our products comply with national and international standards.

Inconel ? 600 is a member of the Inconel family of superalloys. A standard engineering material, this versatile nickel-chromium alloy has high corrosion and heat resistance.

Monel K500 bolts and nuts are used in a variety of industries due to their high temperature resistance, high corrosion resistance and durability. It is a nickel-copper alloy with a composition of 63% nickel and 27% copper, among other elements. HT PIPE is a leading manufacturer of Monel K500 Bolts and Nuts of all types and sizes. Fastener applications include the offshore petroleum industry, power plant applications, petrochemicals, gas handling units, specialty chemicals, pharmaceuticals, equipment, seawater applications, heat exchangers, condensers, and the pulp and paper industry.

INCONEL C-276 alloy has excellent resistance to a wide variety of chemical process environments, including strong oxidizers such as ferric and cupric chlorides, hot contaminated media (organic and inorganic), chlorine, formic and acetic acids, acetic anhydride, and seawater and brine solutions.

Inconel 625 Bolts were developed in the 1960s as a vapor-lined piping material to provide high strength even in extreme high temperatures ranging from freezing low temperatures to 1800¡ãF. Inconel 625 Bolts, also known as Alloy 625, are known for their amazing ability to maintain strength and heat resistance in and out of corrosive environments.

Inconel bolts, like Inconel 600, 601,625,686,718 & 725 bolts, are a family of nickel-chromium-molybdenum alloys used for their high strength at elevated temperatures and good corrosion resistance. Because of its high thermal stability, Inconel can be used in service temperatures ranging from cryogenic to 2200¡ãF (982¡ãC). The high alloy content of Inconel bolts enable it to withstand a wide variety of severe corrosive environments.

Because of its versatility, and because it is a standard engineering material for applications requiring corrosion and heat resistance, many different critical industries use Nickel Alloy 600 in their applications.

Alloy 600 is non-magnetic, has excellent mechanical properties and a combination of high strength and good machinability, and is easy to weld. Inconel 600 has the cold forming properties typically associated with chrome-nickel stainless steels.

Alloy 31 is a nickel, chromium and molybdenum stainless steel with added nitrogen and copper. Alloy 31 is a nitrogen-added iron-nickel-chromium-molybdenum alloy.

Hastelloy B3 studs are suitable for all applications that previously required the use of Hastelloy B2 alloy. Due to the enhanced thermal stability of Hastelloy B3 square bolts, the problems associated with manufacturing Hastelloy B2 parts are reduced.

Inconel 718 studs and other fasteners have different types of threads. Available in BSW, UNC, BSF, UNF, Metric or others as required.

Similar to Nimonic 75 alloy with good corrosion and oxidation resistance. Creep rupture and tensile properties are high at 815¡ãC (1500¡ãF). It can be hot worked in the temperature range of 1050-1200¡ãC.

Hastelloy C-276 fasteners and other products in the Hastelloy family have excellent resistance to corrosion and oxidizing and reducing chemicals. Due to its adaptability, Hastelloy C-276 alloy can be used in problem areas and is more likely to occur in process areas. In Hastelloy C276 hex bolts, the chromium content is increased to about 21% and the molybdenum content is reduced to about 13%. Hastelloy C276 Heavy Duty Hex Bolts also provide optimum resistance to environments encountered in reducing and oxidizing conditions in the process stream.

Inconel 718 nuts have excellent resistance to chloride ion stress corrosion cracking due to their nickel-chromium content. Nickel in Alloy 718 helps to resist the alkalinity of many inorganic and organic compounds over a wide range of acidity and acidity, with the exception of strongly oxidizing compounds. Its chromium content makes it resistant to sulfur compounds and mild oxidizing media, while molybdenum helps prevent pitting.

La aleacion K500 tiene aproximadamente tres (3) veces el limite elastico y el doble de la resistencia a la traccion de 400 en comparacion con 400. MONEL K500 se puede fortalecer aun mas mediante el trabajo en frio antes del endurecimiento por precipitacion.

Alloy 600 also has excellent mechanical properties with high strength and good machinability.