nickel alloy incoloy 825 female equal straight pipe fitting elbows

Due to the addition of chromium, UNS N08800 butt weld elbows are resistant to oxidizing media such as nitric acid, salts and nitrates. These nickel alloy 800HT elbows can withstand high temperature environments and have a good surface finish.

The specification is for pressure piping and fitting in the high or moderate temperature services.ASTM A234 (ASME SA234) pipe fittings after shaping from an elevated temperature, shall be cooled down to a temperature below critical range under suitable conditions which preventing injurious defects caused by too rapid cooling, but in no case more rapidly than the cooling rate in still air. Referring standard in Section 7 of ASTM A960/A960M.

It exhibits excellent corrosion resistance due to its high chromium, molybdenum and nitrogen content. They are highly resistant to pitting and crevice corrosion even in oxidizing and acidic solutions. Duplex 2205 butt welded pipe fittings are resistant to chloride stress corrosion cracking at temperatures of approximately 150 degrees Celsius. Due to the presence of ferrite in duplex UNS S31803 fittings, they exhibit good performance in corrosive environments and provide good weldability.

A pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction
or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Super Duplex S32950 Fittings are hardened on a variety of parameters such as strength, temperature, pressure resistance and durability before supplied to the customers. These UNS S32950 Super Duplex Pipe Fittings are being offered in an inclusive range such as S32950 Elbow, S32950 Bends, S32950 Equal & Unequal (reducing) Tees, S32950 Equal & Unequal (reducing) Cross, S32950 Concentric & Eccentric Reducer, S32950 End Pipe Cap, S32950 Long & Short Stub-ends, etc.

Tee butt weld fittings are made from A312 dual certified 304/304L or 316/316L stainless steel with milled inside and outside diameters (ID/OD). These stainless steel welded joints meet ASTM A403, ASTM A960, MSS SP-4, ASTM B16.9 (except for walls) and MSS SP-43. Schedule 10 fittings are nominal pipe size (NPS), not pipe outside diameter (OD). Schedule 10 pipe and fittings have wall thicknesses that are nearly twice as thick as standard 16 gauge pipe OD fittings, making them ideal for custom turbine manifold and downpipe fabrication. The increased wall thickness provides additional durability and is less prone to cracking under the high thermal stress of exhaust gas temperatures.

The higher strength results from close control of carbon, aluminum, and titanium contents in conjunction with a high temp anneal.

We insist on trying our fittings during processing to make sure it’s the ideal variety. Incoloy WNR 1.4876 Equal Diameter Tee Fittings are known for their robust construction, perfect finish, dimensional accuracy, elegant design, high reliability, perfect insulation and more. It is also known for its low maintenance, high durability, perfect design, easy operation, finish, simple installation, durability, perfect size, etc. To stay top-notch, it’s synthetic under the guidance of corporate experts. The pipe fittings we provide are widely demanded in enterprises because of their advanced and first-class construction and inflexible construction.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

The combined effects of mechanical and thermal processing of Incoloy Alloy 800HT permit higher design stresses to be incorporated than are permitted for the conventional Alloy 800H.

Traditionally, duplex steels have a chromium content of about 22% by weight. Likewise, stainless grade 2205 is a duplex stainless steel with 22% chromium in the alloy. The higher chromium content in Duplex 2205 fittings provides several benefits, including higher yield strength, better mechanical properties, and excellent corrosion resistance.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

ASTM A403 WP317 Pipe Fittings could be a altered adaptation of Stainless Steel 317L Pipe Fittings. It has high quality and erosion resistance.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

However, titanium can lose its strength at temperatures greater than 430?C because it is not as hard as high grades of steel.

Duplex stainless steels are a family of stainless steels. These are called duplex (or austenitic-ferritic) grades because their metallurgical structure consists of two phases, austenite (face-centered cubic lattice) and ferrite (body centered cubic lattice) in roughly equal proportions. They are designed to provide better corrosion resistance, particularly chloride stress corrosion and chloride pitting corrosion, and higher strength than standard austenitic stainless steels such as Type 304 or 316.

Grade 316 pipe bend is readily workable, by the standard methods of sheet metal working, with the exception that it cannot be oxygen cut. Plasma cutting is normal. The deep drawing capability of grade 316 is outstanding, because of its high austenite stability.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Reducing tee, generally a professional term, tee for pipe fittings, pipe connectors, used in the main pipe to branch pipe.Reducing tee is a kind of tee, the tee has two kinds: general equal diameter tee and reducing tee.Named because the three ends can be connected to the pipe.

ASTM A403 WP316 fittings are available in different sizes and shapes in pressure ratings 3000#, 6000# and 9000#. Stub end fittings are often used to close one end of a pipe.

Nickel alloys are used in applications involving elevated temperatures, corrosion , or both. Chemical processing equipment relies on the corrosion performance over a wide range of environments.

C-276 alloy is normally solution heat-treated at 2050¡ãF (1121¡ãC) and rapid quenched. If possible, parts which have been hot-formed should be solution heat-treated prior to final fabrication or installation.

These fittings contain small amounts of additional copper, titanium and molybdenum, which improve their chemical and mechanical properties. Our UNS N08825 Incoloy 825 elbows have been designed to provide increased resistance to crevice and pitting corrosion and to operate smoothly at moderately elevated temperatures.

Other available materials include silicone, rubber compounds, galvanized steel, and nylon. These sanitary fittings are primarily used to connect hoses to valves, water pumps, and deck drains.

Typical industrial fields of SUS 316 butt welded pipe fittings are brewing, chemical industry, dairy products, food processing, marine equipment, petrochemical, pharmaceutical, etc. Typical product applications for these ASME SA182 SS 316 fittings are condensers, heat exchangers, filters, pressure vessels, valves, etc.

In these standard Grade WPB is the most common material used for medium and high temperature pipelines. W means weldable, P means pressure, B is grade b, refer to the minimum yield strength.

There are the pressure grade ASTM A234 WPB Pipe Fittings in ? inches to 24 inches nominal bore sizes with different wall thicknesses that correspond to the schedules.It does not cover cast welding fittings which refered standards are ASTM A216/A216M and A217/217M.