Nimonic 80A hex scoket head cap screw m110 bolt

Inconel 625 Bolts were developed in the 1960s as a vapor-lined piping material to provide high strength even in extreme high temperatures ranging from freezing low temperatures to 1800¡ãF. Inconel 625 Bolts, also known as Alloy 625, are known for their amazing ability to maintain strength and heat resistance in and out of corrosive environments.

Inconel 625 bolts are primarily used in circulating cooling and heating applications. They can be used in resistance welding applications. Bolts are used in engine casings, honeycomb structures and hydraulic lines. HT PIPE is a leading manufacturer and supplier of Inconel 625 Bolts in different types and sizes. The material is resistant to crevice and pitting corrosion.

Monel 400 Bolts and Nuts are made from a nickel-copper alloy for extreme corrosion resistance, especially in sour conditions. The material is also strong and rigid and can be used to produce bolts and nuts for high temperature service. HT PIPE is a leading manufacturer and supplier of Monel 400 Bolts and Nuts of all sizes and types. Among the ingredients are carbon, aluminum, manganese, silicon, iron, sulfur and 63% nickel and 28% copper. This composition gives the material a high melting point.

Alloy 926 (1.4529) screws are the perfect replacement for 316L when higher corrosion resistance is required without increased strength. Alloy 926 fasteners are considered a 6-molybdenum alloy (6-molybdenum or 6% molybdenum), similar to sister alloys AL6XN and SMO 254. In the stainless steel category, these 6 molybdenum alloys are considered very corrosion resistant.

Inconel 625 bolts have a high density of 8.44 grams per cubic centimeter. The material also has high strength values. The minimum tensile strength of the fastener is 880MPa and its minimum yield strength is 460MPa. Inconel 625 nuts have 50% elongation and good electrical resistivity.

This nickel 2.4816 bolt is inherently non-magnetic. Inconel 600 Nuts and Bolts have excellent mechanical properties, offering buyers an advantageous combination of high strength and good weldability over a wide temperature range. The high nickel content in Inconel 600 screws allows them to maintain considerable resistance under reducing conditions. The nickel content in Alloy 600 bolts makes the fastener resistant to corrosion by a variety of organic and inorganic compounds. For example, Inconel 600 bolts have excellent resistance to chloride stress-related corrosion cracking, while also exhibiting excellent resistance to alkaline solutions.

Inconel bolt fasteners consist of three parts – a head at the top, a long cylinder with external threads, and a chamfer at the bottom.

HASTELLOY(r) C276 can be formed by cold working using conventional techniques.

Alloy 20 is designed to withstand sulfuric acid. Its nickel, chromium, molybdenum and copper content all provide excellent general corrosion resistance. Alloy 20 fasteners are austenitic stainless steel fasteners made from alloys containing limited carbon content of chromium, nickel, molybdenum, and nitrogen.

Nimonic 80A is a precipitation hardenable nickel-chromium alloy. It has been largely replaced by Nimonic 90 and Inconel X-750, but it is still specified for nuclear applications due to its low cobalt content.

Inconel 926 bolt material meets ASTM B446, B564, F467, F468, UNS N06926, DIN EN 2.4856, AMS 5666 and BS 3076 specifications and is adequate for high strength, corrosion resistance and high temperature applications up to 1000o C (1800o F).

Hastelloy X fasteners, also known as UNS N06002 fasteners, have excellent corrosion resistance and high temperature strength. It is very resistant to stress corrosion cracking but has excellent ductility when subjected to 16,00 hours of torture at temperatures up to 1,600F. It is also suitable for furnaces, heaters and many high temperature applications because it is weldable, heat treatable and relatively easy to machine. That’s why we think Hastelloy X fasteners basically offer the best of both worlds – corrosion and heat resistance.

Hastelloy C276 is an extremely versatile material that has been used in a variety of harsh environments. It exhibits corrosion resistance to chloride-containing media, organic acids, oxidizing media, reducing acids, seawater and brine, and sulphur-containing flue gas. Hastelloy C276 replaces Alloy C (UNS N10002), which has slightly lower chromium and molybdenum contents. The high nickel, molybdenum and tungsten contents make them expensive compared to austenitic stainless steels. It is by far the most popular super alloy.

Inconel 600 Bolts are composed of Chromium, Nickel and Molybdenum. This makes these bolts superior to stainless and carbon steel bolts. The lengths of these bolts are between 3mm and 200mm. Inconel 600 Hex Bolts are highly resistant to corrosion and oxidation. These bolts are designed to handle extreme temperatures and high pressures.

Hastelloy X Bolts have been widely used in combustion zone components of turbine engines such as transition ducts, combustion chambers, booms and flame holders, as well as afterburners, exhaust pipes and cabin heaters. This alloy is recommended for industrial furnace applications due to its unusual resistance to oxidation, reduction and neutral atmosphere.

Inconel 718 Bolts exhibit extremely high yield, tensile and creep rupture properties at temperatures up to 1300¡ãF.

INCONEL 718 is a high nickel superalloy commonly used in the oil and gas, petrochemical and gas turbine industries. It has excellent mechanical strength, in addition to high corrosion resistance.

Alloy31 is a nitrogen-added iron-nickel-chromium-molybdenum alloy. This alloy fills the gap between special alloys austenitic stainless steels and nickel alloys. Alloy 31 has been proven in the chemical and petrochemical industries, ore extractors, environmental and marine engineering, and oil and gas production.

Monel K500 Fasteners are precipitation hardenable nickel and copper base alloy fasteners. These fasteners are developed for the excellent corrosion resistance adding with benefits of great hardness and strength.

Alloy 20 bolts offer users a combination of nickel, chromium, molybdenum, and copper which provides good general corrosion resistance. Alloy 20 (2.4660) bolts are best suited for mid-range corrosion use ¨C better than steel alloys but not at the level of high performance nickel based alloys like Hastelloy C276.

Hastelloy B3 bolts are also known as alloy B-3 bolts and can be found under UNS N10675. This alloy is extremely resistant to pure hydrobromic, sulfuric and hydrochloric acids. Many industries, including the chemical industry, consider the alloy easy to machine, and its ductility allows machinists to easily form and even weld.

Hastelloy C276 bolts are used in heavy duty applications due to their excellent mechanical quality. This material is one of the most corrosion-resistant materials used in the world. The bolt can be used with welding without the effects of grain boundary precipitation because it has virtually no carbide precipitation during welding. Hastelloy C276 bolts can be used in acid treatment applications because the material resists most corrosive conditions, including heavy sulfur compounds and chloride ions. This quality makes it suitable for desulfurization machinery, flue gas machinery and other harsh conditions.

Alloy B (UNS N10001) was developed to resist hydrochloric acid. Hastelloy B2 has replaced it. Alloy B3 (UNS N10675) is a newer variant with higher thermal stability. These alloy B2 bolts are a wrought nickel molybdenum alloy that can be used in the as-welded condition. It is highly resistant to hydrochloric acid of all concentrations and temperatures. Known as UNS N10665 bolts, these bolts are also resistant to stress corrosion cracking and pitting.

Nimonic Alloy 80A is a nickel-chromium alloy with good oxidation and corrosion resistance. Nimonic Alloy 80A also has high creep rupture and tensile properties at temperatures up to about 815?C. Alloy 80A is precipitation hardened by the addition of the elements aluminium and titanium.

Alloy31 is a nitrogen-added iron-nickel-chromium-molybdenum alloy. This alloy fills the gap between special alloys austenitic stainless steels and nickel alloys. Alloy 31 has been proven in the chemical and petrochemical industries, ore extractors, environmental and marine engineering, and oil and gas production.

It is used in flue gas desulfurization systems because of its excellent resistance to sulfur compounds and chloride ions encounted in most scrubbers.

Since iron is its most abundant constituent, it is classified as super-austenite. Even though its nickel content is less than half, the UNS system classifies alloy 20 as a nickel-based alloy. Alloy 20 is resistant to hot sulfuric acid, while Alloy 20 is stabilized with columbium to minimize carbide precipitation during welding. It has very good mechanical properties and can be manufactured relatively easily. Although the alloy was designed for industries related to sulfuric acid, it is widely used in the chemical industry all over the world.

INCOLOY alloys belong to the category of super austenitic stainless steels. These alloys use nickel-chromium-iron as the base metal and add additives such as molybdenum, copper, nitrogen and silicon. These alloys are known for their excellent strength at high temperatures and good corrosion resistance in a variety of corrosive environments.

Inconel 600 Fasteners are also sometimes referred to as Alloy 600 Fasteners or UNS N06600 Fasteners. This alloy has high heat and corrosion resistance. Inconel 600 fasteners have high tensile strength and good processability, making them ideal for the following applications: bubble columns, stills, heaters, fatty acid concentrators, trays and pulp/paper conditions. Inconel is a nickel-chromium-iron alloy that can only be strengthened by cold working. Due to its high nickel content, this alloy is highly resistant to many inorganic and organic compounds and is virtually immune to chloride ion stress/corrosion cracking.

INCONEL 625 is a nickel-chromium alloy with an addition of molybdenum and niobium. These additions give the alloy better mechanical properties and better corrosion resistance without having to harden the material.