Nimonic 80A hex scoket head cap screw m14x1.5 bolt

Alloy 600 also has excellent mechanical properties with high strength and good machinability.

Inconel 625 also has resistance to various aqueous media causing localized corrosion, stress corrosion cracking and other forms of attack.

Inconel 625 is a nickel-chromium-molybdenum alloy with added niobium that works with molybdenum to strengthen the alloy’s matrix for excellent strength and toughness.

INCONEL 718 is a high nickel superalloy commonly used in the oil and gas, petrochemical and gas turbine industries. It has excellent mechanical strength, in addition to high corrosion resistance.

Welding of this alloy is similar to that of the C-22 alloy. Gas tungsten arc welding (GTAW) and shielded metal arc welding (SMAW) are commonly used to weld C-276 alloys.

It is recommended that the alloy be welded in the solution annealed condition with C-276 filler metal.

Due to the alloy’s good corrosion resistance, Inconel 718 Hex Head Bolts have been used in food processing equipment, caustic solutions, and general corrosion resistant parts and structures.

Inconel alloy 718 hexagon bolts have good comprehensive performance in the temperature range of -253 ~ 700 ¡æ. The yield strength below 650¡ãC ranks first in the deformed superalloy, and has good fatigue resistance, radiation resistance, oxidation resistance and corrosion resistance, good processing performance, and good welding performance.

Inconel 718 Nut is an age-hardening nickel-chromium-based superalloy ideal for extreme environments where oxidation and corrosion resistant bolts are required, even when subjected to pressure and high temperatures. 718 nuts are twice as strong as Inconel 625 nuts and are known for their high yield strength and 1800¡ãF availability. Inconel 718 nuts are often chosen by the industry for their high temperature strength capabilities, it also provides strength and ductility at low temperatures.

Hex bolts are used to fasten two or more parts together to form an assembly either because it cannot be manufactured as a single part or to allow for maintenance and repair disassembly. By definition “A Bolt is a headed and externally threaded mechanical device designed for insertion through holes in assembled parts to mate with a nut and is normally intended to be tightened or released by turning that nut.” When used with a preformed internally threaded (tapped) hole, the hex bolt’s head is turned to tighten, which technically makes it a screw (see our Tech Data section for a discussion regarding the differences between bolts and screws). Hex bolts are also known as: hex head bolts, cap screws, hex cap screws, hex head cap screws, machine bolts, hex machine bolts, hex head machine bolts and, if fully threaded, tap bolts, hex tap bolts and hex head tap bolts. A hex bolt is often differentiated from a hex cap screw by its underhead bearing surface: if it has a circular boss, called a washer face, it’s a hex cap screw¡ªif it doesn’t then it’s a hex bolt.

Alloy C-276 has excellent resistance to pitting and stress corrosion cracking. It is also one of the few materials that can withstand the corrosive effects of wet chlorine, hypochlorite and chlorine dioxide.

Inconel 625 bolts have a high density of 8.44 grams per cubic centimeter. The material also has high strength values. The minimum tensile strength of the fastener is 880MPa and its minimum yield strength is 460MPa. Inconel 625 nuts have 50% elongation and good electrical resistivity.

926 is an austenitic stainless steel alloy with a chemical composition similar to alloy 904L with 0.2% nitrogen and 6.5% molybdenum. The content of molybdenum and nitrogen significantly increases resistance to pitting and crevice in halide media. At the same time, nickel and nitrogen not only ensure the metallographic strength, but also reduce the separation of the intergranular thermal tendency. Alloy 926 is a super austenitic molybdenum stainless steel with excellent resistance to a variety of highly corrosive environments. They are used in a variety of heavy duty applications including chemical storage and processing, aerospace and food processing.

The composition of Monel K500 fasteners includes carbon, 2.3% aluminum, manganese, silicon, iron, sulfur and titanium in addition to nickel and copper. It is this unique composition that gives the material its superior strength, extreme corrosion resistance and ductility. Applications for these fasteners include the offshore petroleum industry, power plant applications, petrochemicals, gas handling units, specialty chemicals, and more.

The Stud Bolt is a threaded rod with 2 heavy hexagon nuts, while the Hex Bolt has a head with one nut. Nuts and head are both six sided. Bolts threading are defined in ASME B1.1 Unified Inch Screw Threads, (UN and UNR Thread Form). The most common thread is a symmetrical form with a V-profile. The included angle is 60¡ã. This form is widely used in the Unified thread (UN, UNC, UNF, UNRC, UNRF) form as the ISO / metric threads.

Hastelloy B2 studs have poor corrosion resistance to oxidizing environments and are therefore not recommended for use in oxidizing media or in the presence of iron or copper salts as they may cause rapid premature corrosion failure.

Monel K500 Washers have the same basic iron and carbon composition, but steel also contains a healthy dose of chromium that gives its famous corrosion resistance.

It is used in chemical processing, pollution control, pulp and paper production, industrial and municipal waste treatment and the recovery of ¡°sour¡± natural gas.

HT PIPE manufactures Inconel Alloy 718 fasteners such as nuts, bolts, socket head cap screws, washers, studs, studs, socket head cap screws, countersunk socket head screws and machined parts as well as hot forgings.

Monel bolts, like Monel 400 and K500, are made from a nickel-copper alloy and exhibit high strength, toughness and good corrosion resistance over a wide temperature range.

Hastelloy X alloy fasteners are precisely engineered by our experts to ensure the finest steel is used in industrial processes. Because of its unfamiliar resistance to reducing, neutral and oxidizing environments. Hastelloy X alloy fasteners have also been found to have significant SCC resistance in petrochemical functions. Hastelloy X alloy is a chromium-iron-nickel-molybdenum superalloy with excellent high temperature efficacy, machinability and oxidation resistance.

MONEL K500 es una aleacion de niquel-cobre que se puede endurecer por precipitacion mediante la adicion de aluminio y titanio.

Since iron is its most abundant constituent, it is classified as super-austenite. Even though its nickel content is less than half, the UNS system classifies alloy 20 as a nickel-based alloy. Alloy 20 is resistant to hot sulfuric acid, while Alloy 20 is stabilized with columbium to minimize carbide precipitation during welding. It has very good mechanical properties and can be manufactured relatively easily. Although the alloy was designed for industries related to sulfuric acid, it is widely used in the chemical industry all over the world.

Alloy 20 is an upgrade to 316 stainless steel. Since iron is its most abundant constituent, it is classified as super-austenite. Even though its nickel content is less than half, the UNS system classifies it as a nickel-based alloy. Alloy 20 is resistant to hot sulfuric acid. It is often found in chemical mixers and fertilizer manufacturing equipment. In general, it is an economical alternative to alloy C276 and other materials with a higher nickel content.

It is usually used in Thermocouple sheaths. Ethylene dichloride (EDC) cracking tubes.

Nickel-based alloys are very useful materials for making high-quality tubular products. One of the key reasons is their excellent corrosion resistance in both waterborne and high temperature applications.

Monel K500 bolts are comprised of a nickel alloy that combines the outstanding corrosion resistance of Monel 400 with increased strength and hardness.

Inconel 625 Spring Washers is commercially pure wrought alloy with a lower carbon content to prevent embrittlement by inter-granular carbon at elevated temperatures. Inconel 625 Wire Spring Washers has characteristics that are useful in several fields, notably chemical processing and electronics. Inconel 625 Flat Spring Washers are also known as solid solution strengthened and commercially pure wrought materials.

Nimonic 80a washers are low creep superalloy fasteners made from an alloy containing over 50% nickel, 20% chromium with additions of titanium and aluminum. Nimonic Alloy 80a fasteners can withstand very high temperatures.

Inconel 718 fasteners have been used in environments from -400o F (-250o C) to 1300o F (700o C). Typical applications include gas turbine parts and cryogenic storage tanks.

Hastelloy C22 fasteners are a general-purpose grade composed of chromium, nickel, molybdenum and tungsten alloys. These designs are designed to increase resistance to pitting, stress corrosion cracking (SSC) and crevice corrosion cracking. It has high chromium content and good resistance to oxidizing media. The presence of molybdenum and tungsten provides good resistance to reducing media. Its nickel content provides admirable resistance to oxidizing aqueous media.