one-eighth to 6 inch size nickel alloy pipe fitting ASTM B366 UNS N06625 Tees

A pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction
or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

The key properties of stainless steel 310S end cap fittings are their high chromium and moderate nickel content, making them key properties against oxidation, sulfidation, and other forms of hot corrosion.

Inconel 601 ( UNS N06601 ) nickel-based alloy Elastic modulus: 124.7-206.5GPa.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

Fittings are used to change the direction of the pipe. The easiest way is to bend the pipe. However, it stretches and thins the outer wall of the pipe. It also thickens the inner walls of the pipe. 2205 duplex stainless steel fittings are known for their austenitic and ferritic microstructures. They show the properties of both classes. ASME SA815 Duplex Steel Butt Welded Pipe Fittings show improved localized corrosion resistance compared to Grades 316 and 317.

N04400 is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Alloy N04400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acid-like substances), brine, hydrofluoric acid, and sulfuric acid. Other advantages of using this alloy are toughness and high strength over a wide temperature range; it can also be manipulated to be magnetic if desired.

WPHY 52 Fittings are recommended be heat treated by one or more of the following procedures: annealing (stress relieving), normalizing, normalizing and tempering, quenching and tempering.Made utilizing high-grade crude materials, these ASTM A860 WPHY Pipe Fittings are anti-corrosive and strong.

Duplex Steel S31803 Front Ferrule Fittings are used in commercial and aerospace applications and can be freely formed and have best-in-class weldability. Given that the dual-phase steel S32205 rear ferrule joint is only about one-third the weight of comparable steel parts, it is the clear choice when weight is an aspect.

304 and 304L are austenitic alloys, which means that iron carbide or a non-magnetic solid solution of carbon in iron is used to impart corrosion resistance to this stainless steel. We manufacture stainless steel 304/304L forged fittings in socket weld and threaded forms as well as stainless steel 304/304L elbows in standard and non-standard sizes with bend radii from 1D to 10D. We offer stock delivery of Stainless Steel 304/ 304L Fittings, Stainless Steel 304/ 304L Flanges and Stainless Steel 304/ 304L Bends in a variety of standard sizes and types.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.?Butt-weld and forged fittings are available.Excellent corrosion resistance in many acidic and alkaline environments Especially suitable for reducing conditions. Good ductility and thermal conductivity Ideal for seawater applications.

SA403 wp304 pipe end caps cover pipe ends, stop fluid flow and protect pipe threads. In multi-end fittings, it is often used to direct flow to a specific end.

ASTM A815 UNS S32760 capis available at our company on a large-scale. The UNS S32760 standard of pipe fittings is considered one of the best in the industry due to its mechanical properties.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Hastelloy B3 pipe fittings is a Nickel, Molybdenum, and Chromium alloy which has excellent resistance to pitting, corrosion, stress-corrosion cracking plus and thermal stability superior. Alloy B3 exhibits excellent resistance to sulfuric, acetic, formic and phosphoric acids, and other non-oxidizing media.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Generally speaking, carbon steel pipe fittings and flanges are widely used in applications that do not require higher corrosion resistance materials such as stainless steel and nickel alloys. Carbon steel products are easy to corrode and rust when exposed to water.

They can be annealed and hardened through a cold working process. They can withstand service containing nitric and phosphoric acids and the resulting oxidation. We provide third-party inspection services to large companies. We also offer a variety of Stainless Steel ASTM A403 WP316L Fittings such as SS WP316L Tee, WP316L SS End Cap, SS 316L Reducer, SS 316L Cross, SS 316L Elbow, SS 316L Stub End, etc.

Duplex steel UNS s31803 pipe fittings are mass produced and widely used duplex steels. This grade of steel can withstand stress corrosion cracking due to contact with sulfur. UNS S31803 elbow grade is inherently economical and reliable as it provides longer service life. Duplex steel UNS S31803 fittings are easy to weld and will not expand at high temperature and stress levels.

Monel K500 pipe bend and elbow are virtually nonmagnetic, even at quite low temperatures

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

When titanium is mixed with other metals, the alloys can reach a tensile strength of more than 1,400 MPa, which makes 200,000 psi.

A reputed distributor and supplier of Duplex S31803 Fittings, the most widely used duplex (ferritic/austenitic) stainless steel grade. We recognize the importance of supplying raw and pre-machined duplex UNS S31803 welded butt welded pipe fittings that are trusted for quality, mill source traceability, supply accuracy and fast delivery. Duplex UNS S31803 Elbow Fittings are extremely corrosion resistant and work hardenable alloys.

Nickel alloy long radius elbows Nickel alloy long radius elbows without drilling holes are called long radius elbows and are used to close the end of the pipe. Long radius elbows are available in threaded or welded form from 150 lbs to 2500 lbs. 200 Nickel Alloy Long Radius Elbow, 201 Nickel Alloy Long Radius Elbow, 20 Nickel Alloy Long Radius Elbow.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

Type : Seamless / Welded.This steel type contains as low as 0.03% of carbon content and thus reduces its susceptibility to intergranular corrosion.

Titanium, zirconium, and silica all belong to the first transition group in the periodic table.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

The alloy has great mechanical properties at subzero temperatures.For catering to the needs of our customers better, it is essential that we manufacture Monel Pipe Fittings in different types, with each one serving some specific purpose.