pipe a335

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

The P2 and P12 steel pipes of A335 should be made by the coarse grain melting method. Steel should meet chemical composition, tensile properties and hardness requirements.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

Besides these elements the addition of trace amounts of both Manganese and silicon, other set of common alloying elements, provides the alloy steel threaded flanges with excellent deoxidizing capabilities.

Bolts are chrome molybdenum heat treated steel according to ASTM A193 B7m specification for bolts. The primary alloy components of ASTM A193 Grade B7 bolts are chromium and molybdenum. These ASTM A193 B7 Metric Bolts are manufactured by heat quenching and tempering. Heat treating A193 B7 bolt material helps to develop desired mechanical properties such as increased tensile strength of ASTM A193 B7 hex bolts after heat treatment.

In addition to good corrosion resistance, the addition of chromium and molybdenum to the alloy enhances its ductility.

800H can resist corrosion of many corrosive media. Its high nickel content makes it resistant to stress corrosion cracking in aqueous corrosion conditions. The high chromium content provides better resistance to pitting and crevice corrosion cracking. The alloy has good corrosion resistance to nitric acid and organic acids, but limited corrosion resistance in sulfuric acid and hydrochloric acid. Good corrosion resistance in oxidizing and non-oxidizing salts, in addition to the potential for pitting corrosion in halides. It also has good corrosion resistance in water, steam and mixtures of steam, air and carbon dioxide.

WPHY 52 Fittings are recommended be heat treated by one or more of the following procedures: annealing (stress relieving), normalizing, normalizing and tempering, quenching and tempering.Made utilizing high-grade crude materials, these ASTM A860 WPHY Pipe Fittings are anti-corrosive and strong.

A182 F5 material is an excellent alloy that is hardened only by cold working. It is often used in nuclear energy, medical equipment, chemical energy, etc. These ASTM A182 Grade F5 Flanges gives extraordinary erosion resistance in, for instance, caustic and acidic applications which includes sulphuric and higher chloride environments.

Alloy steel sounds like: steel that contains a specific amount of alloying elements. Generally, alloying elements make steel stronger and more resistant to shock or stress. While the most common alloying elements include nickel, chromium, molybdenum, manganese, silicon and copper, many other alloying elements are also used in the production of steel.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.42

When moving high-temperature or corrosive media through Chrome Alloy Pipe from one process to the next, flanges capable of withstanding harsh environments are critical

ASTM A182 Gr F11 class 2 pipe flange has low thermal conductivity and moderately low tensile strength and also has many other properties like great quality, toughness and many other points.

ASME SA 335 grade P22 alloy steel pipe can withstand high pressure and high temperature. Therefore, ASTM A335 P22 pipe is used in applications that need to operate at high pressure and high temperature.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.42

ASTM A193 Grade B7 specification covers requirements for high tensile alloy steel bolting material for use in high temperature or high-pressure service and other special purpose applications.

Alloy Steel Flanges, Alloy Flanges are carefully designed using current technology under the visionary guidance of accomplished professionals in the manufacturing sector.

Alloy Steel F9 Threaded Flanges is 100% recyclable, where 50% of new steel is produced using re-softened scrap metal rendering it an Eco-friendly material. There are different classes to indicate the pressure capacities of the flanges. The AS A182 F9 RTJ Flanges are a special type of flanges because they come in two parts that have two rings that are welded to the pipe ends first and then the pipes are brought together by welding.

ASTM A335 P11 is part of ASTM A335, Pipe shall be suitable for bending, flanging, and similar forming operations, as well as fusion welding. The steel shall meet the requirements of chemical composition, tensile properties and hardness. Each pipe shall be hydrostatically tested. In addition, each pipe shall be inspected in accordance with the practice required for non-destructive testing.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.45

Alloy 20 (Alloy 20) is an iron-based austenitic alloy developed to resist sulfuric acid corrosion. It has excellent resistance to sulfuric acid corrosion; it has strong resistance to phosphoric acid, nitric acid and chloride environments, chloride stress corrosion, pitting corrosion and crack corrosion. Therefore, alloy 20 has the name of anti-corrosion alloy; it has a wide range of applications: such as: chemical, food, medicine, power production and plastics industries will use it. For resistance to pitting corrosion and chloride corrosion, stress corrosion cracking problems, etc., alloy 20 is often used.

These flanges are available in different types such as slip flanges, blind flanges, butt weld flanges, socket weld flanges, orifice flanges, eyeglass blind flanges, threaded/threaded flanges, reducer flanges, ring flanges Type joint flange (RTJ), etc.

ASTM A193 Grade B7 specification covers the requirements for high strength alloy steel bolting materials for high temperature or high pressure service and other special purpose applications. It is a standard specification that defines typical chemical composition, mechanical properties, hardness requirements, preferential heat treatment, product marking, certification, and other requirements for bolted connections used in pressure vessel service, valves, flanges, and fittings. ASTM A193 defines SI (metric) and inch-pound units.

When connecting these parts, put gasket in the middle of two flanges, then tightening the flange screws, so the two will be connected together tightly.

There are different types and grades of the blind flanges as well. There are other different types of ASME SA 182 AS Pipe Flanges such as the weld neck flanges and socket weld flanges each specified for a particular role

ASTM A335 P5 pipe can be fully annealed or isothermally annealed, normalized and tempered as heat treatments to increase hardness. This grade is available in welded and seamless pipe, A335 P5 welded pipe is available in different wall thicknesses and diameters.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P121

The precise properties of our A335 tubing meet the most stringent requirements. We meet all requirements for standard and non-standard size alloy steel products. We are a regular supplier of alloy steel products in a variety of styles, standards, models and custom sizes.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.31

One of the top stocks of ASTM A182 alloy steel F5 flanges for a variety of industrial applications. With a talented team of professionals, we are committed to supplying the highest quality ASTM A182 Alloy Steel F5 Flanges, widely used by customers in suitable applications.

WPHY 52 chemical composition are known for accurate dimension, corrosion resistance and their durability.

S32205 is a duplex stainless steel with twice the strength of austenitic stainless steel. Duplex stainless steel composed of 21% chromium, 2.5% molybdenum and 4.5% nickel-nitrogen alloy. It has high strength, good impact toughness and good overall and local stress corrosion resistance. The yield strength of duplex stainless steels is twice that of austenitic stainless steels, a feature that allows designers to reduce weight when designing products, making this alloy more affordable than 316, 317L. This alloy is particularly suitable for use in the -50¡ãF/+600¡ãF temperature range. For applications outside this temperature range, this alloy can also be considered, but there are some limitations, especially when applied to welded structures. Duplex stainless steel has twice the compressive strength compared to austenitic stainless steel, and designers can reduce its weight compared to 316L and 317L. Alloy 2205 is particularly suitable for use in the -50¡ãF/+600¡ãF temperature range, and can also be used at lower temperatures under severe restrictions (especially for welded structures).

Alloy Steel F12 slip on Flanges are made up of chromium molybdenum steel alloy and therefore have a high rupture resistance. They are also preferred due to their light weight because of the low carbon and high alloy nature.Alloy Steel ASTM A182 flanges are very simple to install and have a low center because the pipe occasionally trips into the flanges after welding.

1.4529 German numeral code. Is a super duplex stainless steel, the main components: 20Cr-25Ni-6Mo-1Cu-0.2N corresponding to the United States: N08926, 254SMo…
1.4529 (UNS N08926) has very high resistance to pitting and crevice corrosion in halide media and in acidic environments containing sulfur and hydrogen
It can effectively resist chloride ion stress corrosion, and also has good corrosion resistance and good stability in oxidizing and reducing media.
The mechanical properties are slightly better than 904L, and it can be used in the manufacture of pressure vessels from -196 to 400 ¡ãC.

Alloy steel seamless pipes are widely used in medium and low pressure fluid pipelines, casings, boiler tubes, oil and gas industry, chemical industry, power generation industry, transformers, agriculture, bearings, general engineering, automobiles, hydraulics, railways, mining, construction, aviation Aerospace, medical, defense and electric motors. P91 alloy steel is mainly used in the power industry. For welded structures, the ASME Boiler and Pressure Vessel Code limits the carbon content to less than 0.35%. Alloy steels are ideal for applications that require higher strength, tougher or better wear resistance than standard carbon steel grades.

Our alloy steel pipes and tubes are packaged and delivered in conspicuous packaging in wooden cases, plywood cartons, boxes, pallets to ensure no damage to any product when exported. Additionally, we offer custom packaging options so that customers can order according to their suitability.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.40