Precipitation hardening possible Alloy 500 bar N04400

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

This alloy is not suitable for highly oxidizing acids such as nitric acid and nitrous acid. It is resistant to sulfuric acid up to 80% and hydrochloric acid solutions up to 20%.

We offer W.Nr 2.4360 Monel 400 Male & Female Flanges to the oilfield fabrication, offshore and to petrochemical industries; our flanges are age hardened and are resistant to caustic solutions, seawater, and to chloride solutions and nitric acids, under oxidising and reducing temperatures. HT PIPE takes ultimate pride in offering the above mentioned range of products that fall under the Monel Flanges product type that come in two grades, 400 and K500. Also We offer wide range of Monel ASTM B564 400 Flanges such as Monel 400 Slip On Flanges, Monel K500 Weld Neck Flanges, Monel K500 Socket Weld Flanges, 400 Monel Alloy Blind Flanges, Alloy K500 Orifice Flanges, Monel 400 Spectacle Blind Flanges, Alloy K500 Screwed / Threaded Flanges, Monel Alloy 400 Reducing Flanges, Alloy K500 Ring Type Joint Flanges (RTJ) etc.

The Stud Bolt is a threaded rod with 2 heavy hexagon nuts, while the Hex Bolt has a head with one nut. Nuts and head are both six sided. Bolts threading are defined in ASME B1.1 Unified Inch Screw Threads, (UN and UNR Thread Form). The most common thread is a symmetrical form with a V-profile. The included angle is 60¡ã. This form is widely used in the Unified thread (UN, UNC, UNF, UNRC, UNRF) form as the ISO / metric threads.

Monel 400 bolts can also be used at higher temperatures. While Monel 400 bolts are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 bolts. Even when cooled to the temperature of liquid hydrogen, Monel 400 will not undergo the ductile to brittle transition that can lead to fracture. This is especially unique compared to most ferrous materials, which are generally stronger but very brittle at extreme low temperatures.

Monel K500 alloy has excellent corrosion resistance, and has higher strength and hardness than Monel 400. This is due to the addition of elements such as Al and Ti to the alloy, and after a certain heat treatment, there are dispersed intermetallic compounds on the substrate.

The Monel Alloy 400 Threaded Flanges are fitted with pipes with threads. The male threads on the pipe ends fit with the female threads on the threaded flanges. The ASME SB564 Alloy 400 Socket Weld Flanges are usually welded onto the pipes.

These products are manufactured with the latest technologies using high grade raw materials. We are manufacturer in national & international standards.

INCOLOY alloys belong to the category of super austenitic stainless steels. These alloys have nickel-chromium-iron as the base metals, with additives such as molybdenum, copper, nitrogen and silicon. These alloys are known for their excellent strength at elevated temperatures and good corrosion resistance in a variety of corrosive environments.
The Alloy 800 Elbow is widely used in various industries and is primarily famous for its excellent mechanical properties. The Werkstoff Nr. 1.4876 End Cap has low gas content, low vapor pressure, and high thermo-electric conductivity.

Astm B564 Monel 400 Blind Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Alloy 400 is highly regarded as one of the best performing engineering alloys.

Monel K500 Threaded Flanges (UNS N05500) has resistant to a sour ¨C gas environment. Monel K500 Slip On Flanges is often used in Chemical Process Industry: such as in processes involving organic acids, caustic soda and dry chlorine, production of chlorinated plastics, and more.

Monel 400 is a copper-nickel corrosion resistant alloy, which is a kind of corrosion resistant alloy with the largest usage, the most extensive use and excellent comprehensive performance.

Also known as alloy k500, Monel K500 fasteners and flanges are comprised of a nickel alloy that combines the outstanding corrosion resistance of Monel 400 with increased strength and hardness. Stronger than 400, alloy K500 even retains this strength in corrosive conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.

A standout feature of Monel flanges is their excellent resistance to hydrofluoric acid, a particularly difficult acid to handle, at all concentrations up to the boiling point.

Applications that deal with the marine environment are required to be resilient to the effects of saltwater. After all, the concentration of salt in marine water is about 3.5%, enough to corrode ordinary steels with no protective surface treatment.

Alloy 400 fasteners have a melting point of 1350 degrees Celsius. The density of the material is higher than most chrome-nickel stainless steels. The density of Monel 400 material is 8.8 grams per cubic centimeter. The strength also exceeds that of the 304, 316 and 310 grades of austenitic stainless steels. The minimum yield strength is 240MPa and the minimum tensile strength is 550MPa. UNS N04400 Studs are made from a single strand of Monel 400 material.

The high-temperature plasticity of the experimental alloy added with trace amounts of Mg, Cr and Co is obviously improved, and it exhibits certain superplasticity. At 1010¡æ, the strain rate sensitivity index m is 0.32, and the maximum elongation is 240%.

When utilized at subzero temperatures, these fasteners actually increase their tensile and yield strengths, while ductility and toughness are virtually unchanged. In addition, the flange face differs as flat face, raised face and ring type joint face as well. The Monel Slip On Flange is most useful with seamless pipes. The seamless pipes can easily slip onto the flange and reach the precise connection location. The ASTM B564 Monel 400 Lap Joint Flanges and other flanges can also come as threaded, forged, screwed or plate flange types.

Monel 400 is a Nickel-Copper alloy, resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

Monel 400 es una de las pocas aleaciones que conserva la resistencia a temperaturas bajo cero, asi que utilicela en estas situaciones.

ASME Sb564 Alloy 400 Plate Flanges Monel 400 N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Astm B564 Monel 400 Blind Flanges A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

UNS N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

This nickel alloy is attacked in sulfur-bearing gases above approximately 700¡ã F and molten sulfur attacks the alloy at temperatures over approximately 500¡ã F.

Las aplicaciones tipicas de la alta resistencia y resistencia a la corrosion de MONEL K500 son ejes de bombas, impulsores, ejes de helices, componentes de valvulas para barcos y torres de perforacion en alta mar, pernos, collares de pozos de petroleo y componentes de instrumentacion para la produccion de petroleo y gas.

We are Manufacturers, Supplier and Exporters of Monel K500 Flanges. These Monel R405 flanges are used with stub end or daft which is butt welded to the pipe with the flange loose behind it.

The Alloy K500 Studs are threaded rods with threads on both ends. They can be different types depending on the threaded distance from the center and the thread type. The material is high temperature and high pressure resistant. It has 1350 degrees Celsius melting point, 790MPa minimum yield strength and 1100MPa minimum tensile strength. These values are double the strength of 304 grade.

The levels of molybdenum and copper enable Monel K500 Ring Joint Type Flanges to resist reducing agents and acids. Our wide array of UNS N05500 | Monel K500 Threaded Flanges is utilize in rough oil stills, gas and new water tanks, marine installations and clasp, and concoction preparing gear.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.