round bar sizes A182 F9 bright mild steel round bar

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

It can be used with other a335 gr P22 alloy tube types and fittings. SA 335 gr P22 alloy steel pipe has high heat resistance and low thermal expansion. This property of P22 metal tubing makes it suitable for use in the oil and gas industry, power industry, petrochemical industry and refineries where temperatures often fluctuate at high temperatures.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.44

Low alloy steel ASTM A182 F11 flanges typically have a total alloy content of 1.5% – 5%. Its common alloying elements are manganese, chromium, silicon, nickel, molybdenum and vanadium. It may contain up to four or five different quantities of these alloys. At the same time, the increased strength of the alloy steel F11 flange may require higher forming pressures. Annealing of SA 182 Gr F11 steel flanges is accomplished by water quenching by thorough immersion at 1725¡ãF – 1850¡ãF (941¡ãC – 1010¡ãC) and can only be hardened by cold work.

To be sure, huge numbers of the reactions of Alloy Steel F9 Slip On Flanges meddle with each other, requiring the utilization of process models to help in analysing alternatives, improving contending reactions, outlining productive commercial practices. The specification is for high temperature pressure services. The SA 182 Gr F9 Steel Pipe Flanges come in the size range of ? inches to 48 inches with dimensions varying according to the ASTM, ASME and other international standards.

Low alloy steels contain trace amounts of alloying agents such as niobium, nitrogen, vanadium, copper, nickel, chromium, titanium, calcium, molybdenum, rare earth elements or zirconium.

SA12 F11 Flange is made up of by using supreme raw material and they give excellent performance even in toughest environment. The weight chart of this is also available and based on this the product is manufactured.

Nickel alloy 20 is a low-carbon, niobium-stabilized austenitic nickel/iron/chromium alloy with additions of molybdenum and copper. ASTM B366 specification covers Inconel, Monel, Hastelloy and Nickel Alloy Pipe Fittings used in acidic and sea water.

Chromium (or chromium) in A335 is an essential element in stainless steel production. Steel products are defined as stainless steels with 12% or more chromium added. Chromium is widely used due to its excellent heat resistance properties and is irreplaceable in terms of resistance to oxidation in high temperature applications.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P96

Pipe to ASTM A335 P11 can be cold drawn or hot rolled. Each tube shall be reheated for heat treatment – fully or isothermally annealed, normalized and tempered at a temperature not lower than 1200¡ãF (650¡ãC). Each pipe length shall be hydrostatically tested to ASTM A335 P11, along with dimensional inspection and visual inspection. Longitudinal or transverse tensile tests, flattening tests or bending tests are carried out for each heat.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P129

The Alloy Steel Weld Neck Flange has a welded neck onto it that holds larger pipes in place for easy welding and installation.

Regardless of its cost-effective solution, F11-grade rebar is a way to meet the corrosion resistance and mechanical performance requirements set by various industries.

Chrome alloy steel flanges are manufactured in accordance with ASTM A182 F11/F12 and are widely used in nuclear power plants, power plants, water systems, electric power, oil fields, pipeline engineering, natural gas, marine engineering, shipbuilding and other industries. These flanges are harder and stronger than regular steel, but not as corrosion resistant as stainless steel.

The chromium content in the A335 p9 pipe makes it highly resistant to corrosion. Therefore, A335 p9 has excellent high temperature oxidation resistance. In addition to chrome, Astm A335 p9 alloy steel pipe coated with black paint or anti-corrosion oil shows good corrosion resistance. It can also be galvanized with zinc. Galvanizing increases its resistance to atmospheric corrosion.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P147

ASTM A182 F91 is an American standard Martensite type heat-resistant steel forgings, according to ASTM A182-2016.

Monel 400? has low corrosion rate in flowing seawater, therefore it is widely used in marine applications.We make use of the best manufacturing techniques for their production so that the final product being served to the customers is the best of best.

This is the widely used product in many other industries and is thus manufactured with utmost care and the packaging of this is also done with great care and is then dispatched to various other applications.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Alloy Steel Flange Material can differ according to its chemical composition. Low Alloy Steel Flanges are widely used for automotive and aerospace bodies, offshore and onshore structural engineering plates and railway lines.

HastelloyC-276 (Hastelloy) is a tungsten-nickel-chromium-molybdenum alloy with extremely low silicon-carbon content and is considered to be an all-around corrosion-resistant aluminum alloy. The key moisture-resistant chlorine, various air-oxidizing fluorides, isopropyl titanate solutions, hydrochloric acid and air-oxidizing salts, have good corrosion resistance in ultra-low temperature and standing temperature sulfuric acid. Therefore, in the past 30 years, it has been widely used in extremely corrosive natural environments such as chemical plants, petrochemicals, flue gas desulfurization, pulp and paper industry, and environmental protection.

Corrosion resistance

The aluminum alloy has the following characteristics: 1. It has good corrosion resistance to most corrosive substances under the two conditions of air oxidation and repair. ¢ÚIt has good resistance to pitting corrosion, void corrosion and intergranular corrosion. The higher content of Mo and Cr makes the aluminum alloy resistant to corrosion by chloride ion content, and the W element further improves the corrosion resistance. At the same time, Hastelloy C-276 aluminum alloy is one of the only types of raw materials that are resistant to wet chlorine, hypochlorite and chlorine dioxide saturated solutions. Ester solution has obvious corrosion resistance. It is one of the very few raw materials that can be used as a hot sulfuric acid saturated solution.

Too many good properties found in the same product just because of better sheet production. These are high tensile strength, good dimensional accuracy, surface finish, flexibility and durability, withstand heavy loads, strong construction and corrosion resistance. Resistance to corrosion, stress corrosion cracking, crevice corrosion cracking, oxidation/pitting corrosion makes it suitable for a variety of applications.

ASTM A182 Stainless Steel Flanges are manufactured per ASME B16.5 150#, 300#, 600#, 900#, 1500#, 2500#.

The ASTM A320 Grade L7 specification covers stainless steel bolting materials for low temperature service. This standard cover rolled, forged, or strains hardened bars, bolts, screws, studs, and stud bolts used for pressure vessels, valves, flanges, and fittings.

Through tests and production tests, molybdenum in A335 is currently the most effective additive for improving high temperature creep strength. Molybdenum-added seamless steel pipes also show enhanced corrosion resistance and inhibition of pitting corrosion.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P95

We use tested and qualified raw materials to improve the machinability of alloy tubes. These are processed through a metallization process that refines structural and material defects.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.37

The heat treatment could be heat treated according to any of the WPHY 52 specification by either tempering, normalizing, quenching or stress relieving.A860 refers to the high quality of the fittings.

The Welding neck flanges are available across various materials. These materials will have to be as per the Standards set. The materials also should be as per the quality specified by the ASTM or ASME standards.

ASTM A193 Grade B7 bolts and studs are made from chrome molybdenum steel and are quenched and tempered (heat treated) to achieve the desired mechanical properties (strength). Grade B7 is the most commonly used A193 bolt grade in construction.

Commercially pure wrought Nickel with good mechanical properties over a wide range of temperature and excellent resistance to many corrosives, in particular hydroxides.

Good resistance to corrosion in acids and alkalis and is most useful under reducing conditions. Outstanding resistance to caustic alkalis up to and including the molten state. In acid, alkaline and neutral salt solutions the material shows good resistance, but in oxidizing salt solutions severe attack will occur. Resistant to all dry gases at room temperature and in dry chlorine and hydrogen chloride may be used in temperatures up to 550C. Resistance to mineral acids varies according to temperature and concentration and whether the solution is aerated or not. Corrosion resistance is better in de aerated acid.

ASME SA 335 P91 Alloy Steel Pipe also has some other great features like low maintenance, efficient work, high demands, etc. We offer a range of ASTM A335 P91 alloy steel pipes for a wide range of applications in various industries.

ASTM A335 seamless steel pipe is commonly referred to as chrome molybdenum pipe with chemical elements molybdenum and chromium. Molybdenum can improve steel properties such as strength, elastic limit, wear resistance, impact resistance and hardenability.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P93

When the carbon content of the a333 gr 6 welded pipe chemistry is lower, the chance of cracking in the welded area is also lower. However, some manufacturers prefer seamless pipes over welded pipes. The reason behind this is that the performance of the a333 gr 6 seamless tube is almost 20% higher than the welded one in high pressure environments.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.57