s32760 pipe fitting

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

304 Piping Spools are made of 304 Stainless Steel, a common and popular material in many industrial applications that require resistance to corrosion and oxidation. These S30400 Piping Spools are prefabricated using specialized machinery and processes, which ensure that they are highly accurate and reliable.

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

Inconel 718 is a nickel-chromium-based alloy that is commonly used in high-temperature applications such as aerospace and gas turbines. One of the most important factors in the production of ASTM B670 Inconel 718 Sheet is the plate rolling process. There are two main types of Inconel 718 plates available on the market: hot rolled and cold rolled plates.

Stainless Steel 304 Sheet is thin layer of 304 material often up to 6mm in thickness. The sheets come in different widths and lengths. There are different standards to govern the different properties. Roopam Steel is a manufacturer of these sheets in all scales.

A234 Pipe Elbow the radius of curvature is 1.5 times the diameter (R=1.5D). We also accept all orders of CS Elbow A234 WPB up to and including 90 degree to suit your requirements.

Hastelloy B3 Ring Type Joint Flanges is ideally suited for applications requiring corrosion resistance superior to SS 304 and has good elevated temperature strength.

In strong oxidizing solutions like hot, concentrated nitric acid, 600 has poor resistance.

310 and 310s are used in power generation applications; used in gas generator trims, pulverized coal burners and pipe hangers. Sinter plants and cement plants also take advantage of the properties of this stainless steel sheet in burners and burner shrouds, feed, discharge systems and wind boxes.

The pressure-temperature ratings for ASTM A182 F53 flanges are the same as that for other duplex stainless steels.

Hastelloy C-276 is a nickel-molybdenum-chromium-tungsten alloy with excellent general corrosion resistance and good machinability. The alloy should be considered for use in environments requiring resistance to thermally contaminated inorganic acids, organic and inorganic chloride-contaminated media, chlorine, formic and acetic acids, acetic acid, acetic anhydride, seawater and brine solutions.

ASME Sb564 Alloy 400 Plate Flanges Monel 400 N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Stainless Steel 347 Flanges
Featuring 347 stainless steel for very good corrosion resistance, this GRAINGER APPROVED weld neck flange can be attached to a system via a circumferential weld at the neck. The welded area can be easily examined by radiography. Matched pipe and flange bore reduces turbulence and erosion inside the pipeline. Flange is excellent for use in your critical applications and is ideal for use with air, water, oil, natural gas, and steam.

When corrosion resistance is important, stainless steel is an excellent material choice. We offer commercial stainless steel tube and pipe in both welded and seamless, hollow bar, stainless ornamental tubing, stainless steel pipe, Nickel tubing, Nickel pipe. Our most popular offerings are the austenitic grades of 304, 304/L, 316, and 316/L other grades such as 309, 310, 317L, 321, 347, Alloy 200, 400, 600, 800 are available upon request. Material is available in several conditions, including annealed and pickled, bright annealed, mill finished, and polished.

The greatest advantage of Hastelloy B3 bolts compared to B-2 alloys is their ability to maintain excellent ductility during transient exposure to intermediate temperatures.

The ASTM A/ASME SA 335 specification covers seamless ferritic alloy steel pipes for high temperature service. The pipe is mainly used for bending, vanstoning and similar forming operations, as well as for fusion welding.

The advantages of 304 and 304L are their oxidation resistance, excellent formability, ease of manufacture and cleaning, excellent strength-to-weight ratio, and good toughness at low temperatures.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.27

Stainless steel is an alloy of iron that is resistant to rusting. It contains at least 11% chromium and may contain elements such as carbon, other nonmetals and metals to obtain other desired properties. Stainless steel’s resistance to corrosion results from the chromium, which forms a passive film that can protect the material and self-heal in the presence of oxygen.
A stainless steel pipe system is the product of choice for carrying corrosive or sanitary fluids, slurries and gases, particularly where high pressures, high temperatures or corrosive environments are involved. As a result of the aesthetic properties of stainless steel, pipe is often use in architectural applications.

317L is non-magnetic in the annealed condition but may become slightly magnetic as a result of welding.Fittings supplied under this specification shall be examined visually for surface discontinuities, surface checks, and mechanical marks.

The flange material has very high tensile strength of 930MPa and minimum yield strength of 517MPa. This strong material also has 1350 degrees Celsius melting point. This makes the flanges be applied in some of the tough and stressful applications.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

There are many different types of 316 stainless steel. Some common types are the L, F, N, and H variants. Each is slightly different and each serves a different purpose. “L” means 316L steel has less carbon than 316.

Stainless steel 304 is a type of stainless steel that is resistant to corrosion and rusting. Stainless Steel 304 Forged Fittings are used for connecting two pipes or tubes together and can be made from a variety of metals, including copper, brass, aluminum, or stainless steel.

Hastelloy DIN NR. 2.4819 Pipe is a nickel based superalloy. Apart from its primary base alloying element, the alloy for Hastelloy C276 Pipe also contains elements molybdenum & chromium, which results in the alloy gaining certain properties.

Steel pipes are used in structures, transportation, and manufacturing. They are sized according to their outer diameter, with the inner diameter varying based on wall thickness. Some applications need thicker walls than others, depending on the forces the pipe must manage.

Depending on the nature of the application, bars and rods can be used in industry. Stainless steel bars and bars are divided into hot rolled and cold rolled, but cold rolled bars are accurate in size and have the largest supports, supports, motors, etc.

Flanges are usually welded or threaded. Flange joints are made by bolting two flanges together with a gasket between them to provide a seal.

A515 grade 70 carbon steel can be fabricated into pressure vessels for medium to high temperature service. Its machinability is good, similar to ordinary carbon steel.

ASTM A479 Super Duplex UNS S32750 F53 Heavy Hex Nuts are kept together by a combination of their threads’ friction (by means of slight elastic distortion), a small widening of the bolt, and solidity of the components to be held together.

The standard duplex material consists of 22% chromium, 4.5% nickel, 3% molybdenum, manganese, silicon, nitrogen, phosphorus, carbon and sulfur. Duplex 2205 screws and other fasteners have minimum yield strengths up to 97ksi and minimum tensile strengths up to 131ksi. Duplex 2205 hex bolts are nearly twice as strong as austenitic grade steel bolts. They have higher mechanical properties, so 1.4462 alloy 2205 studs and other types of bolts can meet different specifications such as ASME SA 182, 240, 479, 789.

Nickel. The heavy nickel content in Inconel alloys is one of the main sources of the magnetic properties of the alloys. Pure nickel is magnetic, even at room temperature, but is combined with elements such as chromium and carbon when making Inconel alloys.

SB564 UNS N02200 Flange The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

The Stainless Steel 304 Tee or seamless fittings could be used based on the application requirements.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.