Semi Finished Forged Flange A182 F9 WN Flange superior mechanical properties

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

ASTM A194 specification covers carbon, alloy and stainless steel nuts for high pressure and/or high temperature service. American National Standard Heavy Duty Hex Series (ANSI B 18.2.2) shall be used unless otherwise specified. Nuts no more than 1 inch in nominal size shall conform to UNC Series Class 2B.

The range of pipe diameters of A335 that can be tested by each method should be limited by the respective scope of practice. The different mechanical testing requirements for pipes, i.e. transverse or longitudinal tensile tests, flattening tests, hardness or bending tests, are presented.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.22

These well-controlled advantages of Astm a182 alloy steel F9 round bars are evident in automated operations where even modest changes in flow temperature can significantly increase the incidence of scrap.

Ferritic alloy steel pipes are considered to have high chromium concentration and low carbon percentage. These magnetic alloy steel pipes have key qualities including high ductility, corrosion resistance and resistance to stress-related corrosion cracking. Therefore, IBR-certified alloy steel pipes are commonly used in automotive, kitchen and industrial equipment applications.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.63

Schedules vary based on nominal bore diameter in relation to wall thickness. Schedules range from sch20 to XXS. Pipe lengths up to 13500 mm. There are seamless pipes and fabricated pipes in this specification. ASTM A335 P5 pipe can be round, hydraulic, rectangular, square or hexagonal. The length of the pipe can also be cut to length size according to customer requirements.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P148

All chrome molybdenum steel sheets are sedated and heat treated in accordance with ASTM A387, which also specifies minimum and maximum levels of the following elements in steel: Chemicals of Carbon, Manganese, Phosphorus, Sulfur, Silicon, Chromium, Molybdenum, Nickel, Vanadium requirements, columbium, boron, nitrogen, aluminum, titanium and zirconium. A387 boards must undergo product, chemical and tensile testing (documented in the MTC or material test certificate) – must meet specific requirements for tensile strength, yield strength and elongation.

Due to its ease of welding, ASTM A335 Grade P91 Welded Pipe can be welded well into piping systems. Pipes have different tolerance classes and test standards depending on the application requirements, grade, schedule and pressure rating of the pipe material.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.28

ASTM A193 Grade B7M bolts and studs have the same chemical composition as Grade B7 (quenched and tempered medium carbon alloy steel) but have lower strength requirements requiring 100% hardness testing on all fasteners manufactured in the batch. Grade B7M bolts are resistant to chloride, sulfide and hydrogen stress corrosion cracking (SCC) and are often used in sour gas service.

ASTM A335 Grade P11 is also commonly known as ASME SA335 Grade P11 Pipes, it is a seamless ferritic alloy-steel pipe that mainly has high-temperature applications. The UNS designation for this grade P11 is K11597.

We offer a wide range of ASTM A335 P9 alloy steel seamless pipes using high quality raw materials. These alloy steel P9 ERW tubes are forged between 2250¡ãF/1750¡ãF (1230¡ãC/955¡ãC) for 30 minutes per inch of billet or ingot section thickness. These are A335 P9 pipes manufactured to international quality standards. These alloy steel P9 seamless pipes are also available in different sizes, grades, thicknesses and specifications according to customer requirements.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P141

The ASTM B366 Pipe Fittings that we, Steel Tubes India, manufacture, are covered under the specification for nickel alloy pipe fittings and these include the likes of Hastelloy, Inconel, Nickel Alloy and Monel.

Alloy Steel F5 Flanges are square-shaped and are instrumental in interfacing pipes of nominal bore size without welding and are reasonable for high pressure hydraulic frameworks. ASTM A182 F5 Lap Joint Flanges go by a range of names, including back up flange, loose hubbed flange, loose ring flange and van stone flange. ASTM A182 Gr F5 Blind Flanges are commonly used in petrochemical, pipe engineering, public services and water works.

Monel 400? is a nickel-copper alloy that is hardened by cold working only. The various types of available fittings are Monel Stub end, Monel Reducer, Monel End Cap Fittings, Monel tee, etc.

The ANSI B16.5 Alloy Steel Slip On Flange is a flange type that allows the pipes to slip onto the flange and makes the connection in a precise locations.

A blind flange is a solid flange as shown below. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used.

Chrome moly alloy flanges connect pipes, valves, pumps and other equipment, forming a piping system.

800H can resist corrosion of many corrosive media. Its high nickel content makes it resistant to stress corrosion cracking in aqueous corrosion conditions. The high chromium content provides better resistance to pitting and crevice corrosion cracking. The alloy has good corrosion resistance to nitric acid and organic acids, but limited corrosion resistance in sulfuric acid and hydrochloric acid. Good corrosion resistance in oxidizing and non-oxidizing salts, in addition to the potential for pitting corrosion in halides. It also has good corrosion resistance in water, steam and mixtures of steam, air and carbon dioxide.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

ASTM A182 Gr F9 flanges are typically designed for applications with high temperature requirements. Alloys used to produce flanges according to this specification include wrought or rolled alloys and several stainless steel grades.

The addition of molybdenum strengthens the elastic limit of the A335 p11 welded pipe and increases its temperature strength. In addition to these properties, there is a reduction in brittleness and an improvement in the weldability and hardenability of the pipe.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.48

Alloy steel seamless pipes are used in applications that require high precision for ease of installation and accuracy of operation and application. Different types are used for different mechanical benefits. Most applications require a lot of welding, so welding alloy steel pipes is good for them. Some are low in strength but high in corrosion resistance, and some are also high in strength. We offer high strength low alloy steel pipes in various grades and sizes.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.63

Alloy Steel F12 Flanges is effective in nature and is today found used widely in various applications all across the globe in numbers of industries. Alloy Steel F12 Flanges possesses a great resistance to pitting in chloride solutions, a great resistance to crevice and stress corrosion cracking.

L7 threaded studs and short head bolts are readily available in the market.

Despite adding these elements, low alloy steel flanges aren’t necessarily difficult to weld. The key to achieve a successful performance of the welding operation is by knowing exactly what type of low-alloy steel you have.

We offer ASME SA335 Grade P22 Welded Pipe, ASTM A335 P22 Pipe is manufactured according to ASTM standards. Alloy steel A335 P22 ERW tube, Astm A335 P22 temperature extreme cold formed, made from steel strip drawn through a series of rolls.

Manufacturers must adhere to the chemical composition used to produce ASTM A182 F11 Class 2 equivalent grades. Alloy Steel Different alloying agents used in ASTM A182 F11 RTJ flanges, such as phosphorus, silicon, nickel, carbon, manganese, chromium, molybdenum, niobium, titanium, improve fitting performance.

The composition of A335 P91 material contains carbon, manganese, phosphorus, sulfur, silicon, chromium, molybdenum, vanadium, nitrogen, nickel, aluminum, niobium, titanium and zirconium. There are two kinds of seamless pipes and welded pipes. Seamless pipe is drawn from a single raw material billet, while ASTM A335 Gr P91 Welded Pipe is welded from strip or sheet. Welding can be helical or longitudinal from one end to the other to produce the tube. The minimum yield strength of the pipe is 415MPa and the minimum tensile strength is 585MPa.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.60

Grade P11 is known as chrome molybdenum alloy steel. Compared to carbon steel, the properties of this alloy steel are much higher. Typically, alloy steels such as ASTM A335 P11 pipe tend to have much higher element percentages than conventional steels. So take their efficiency to the next level. The alloy composition of the P11 grade consists of chromium and molybdenum, with a chromium percentage of approximately 1.25. The content of molybdenum in the alloy steel P11 seamless pipe is about 0.5%.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P124

A335 P22 is a seamless tube made of ferritic alloy stainless steel. Chemically, the alloy of SA335 P22 material contains trace amounts of carbon, manganese, sulfur, silicon and phosphorus. The main additives in the alloy are molybdenum and chromium, which give stainless steel excellent mechanical properties. Tensile strength, corrosion resistance, hardness and other properties are enhanced and improved. Molybdenum reduces the brittleness caused by the addition of chromium.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P132

Alloy Steel AISI 4140 bar stock or forging stock to produce B7 headed and non-headed bolts. A193 Grade B7 is the most commonly used Bolt specification coupled with A194 Grade 2H Nuts for Bolting Carbon Steel pipeline. A193 B7 bolting is available in metric sizes from M6 to M180 and imperial sizes from 1/4 to 7 inches, in diameter.