semi-finished raw materials of Monel 400 Threaded Elbows for storage tanks of gasoline

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Monel K500 Flanges is further virtually nonmagnetic, even at quite low temperatures. This UNS N05500 Monel are available in various evaluations and sizes, shapes. We offer Monel K500 Blind Flanges that is a unique combination of high strength with similar corrosion resistance to Monel 400 and improved resistance to a sour-gas environments.

Din 931 indicates partially threaded hex head cap screw ¨C The DIN 931 standard will specify the thread tolerance. ? M16; diameter in mm (16 mm) ? In the metric system, all fasteners are assumed coarse thread unless another thread pitch is stated.

Generally, its corrosion resistance is very good in reducing environments, but poor in oxidizing conditions.

The alloy can be machined at satisfactory speeds with machine tools commonly used in the industry. Generally, cold drawn or cold drawn stress relief materials are recommended for the best machinability and smoothest finish.

The strength of this nickel steel alloy is maintained to 1200¡ã F but stays ductile and tough down to temperatures of 400¡ã F. Its melting range is 2400-2460¡ã F.

The chemical composition of Monel K500 Nippo Flanges provides great resistance to a lot of corrosive environments, such as pitting, crevice corrosion, inter ¨C granular corrosion, and stress ¨C corrosion cracking. Monel K500 Spacer Flanges has useful resistance to boiling sulfuric acid up to 40 % concentration, to 60 % concentration at 176 Degree F and in all concentrations to 150 Degree F.

Monel 400 contains the same levels of nickel and copper as the natural nickel ore found.

Monel K500 (alloy K500), UNS N05500 (QQ-N-286), is a precipitation-hardenable nickel-copper alloy that combines the corrosion resistance of Monel alloy 400 with greater strength (over 2x as strong) and hardness. It also has low permeability and is nonmagnetic to temperatures as low as -150¡ãF (-101¡ãC).

Typical application for MONEL K500 which takes advantage of high strength and corrosion resistance are pump shafts, impellers, propeller shafts, valve components for ships and offshore drilling towers, bolting, oil well drill collars and instrumentation components for oil and gas production. It is particularly well suited for centrifugal pumps in the marine industry because of its high strength and low corrosion rates in high-velocity seawater.

Reworking of Alloy K-500 is best done while the material is in the annealed or hot worked and quenched condition. However, age hardened materials can be finished to close tolerances and finish. Therefore, the recommended practice is to machine slightly oversize, age harden, and then finish to size.

MONEL K500 no es magnetico. MONEL K500 debe recocerse cuando se suelda, luego la soldadura debe liberarse de la tension antes del envejecimiento.

Alloy 400 fasteners have a melting point of 1350 degrees Celsius. The density of the material is higher than most chrome-nickel stainless steels. The density of Monel 400 material is 8.8 grams per cubic centimeter. The strength also exceeds that of the 304, 316 and 310 grades of austenitic stainless steels. The minimum yield strength is 240MPa and the minimum tensile strength is 550MPa. UNS N04400 Studs are made from a single strand of Monel 400 material.

We offer a comprehensive range of all types Alloy K500 Flanges grades including Slip on flanges, socket weld flanges, blind flanges, lap joint flanges, screwed flanges, weld neck flanges, reducing flanges, spectacle flanges, slip on flanges, plate flanges, screwed flanges etc.

Monel 400 has excellent corrosion resistance in hydrofluoric acid and fluorine gas medium.

900# Steel Flanges Nickel Alloy Monel 400 Flange Bleed Ring the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

A high nickel alloy with the addition of substantial amounts of copper to give the alloy excellent resistance to sodium chloride solutions, including brine and seawater. Therefore, UNS N04400 Alloy 400 Forged Fittings and Socket Weld Elbows can be used as part of an offshore piping system that may require a change of direction.

Monel 400 flanges are also available for higher temperatures in reduction environments. While Monel 400 flanges are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 flanges.

When in the age-hardened condition, Monel K-500 has a greater tendency toward stress-corrosion cracking in some environments than Monel 400. Alloy K-500 has approximately three times the yield strength and double the tensile strength when compared with alloy 400.

If hardened Monel 400 is the goal, cold working with a soft tooling material is the only option. By cold working, mechanical stress is used instead of heat to change the shape of the metal.

Monel K500 bolts and nuts are used in a variety of industries due to their high temperature resistance, high corrosion resistance and durability. It is a nickel-copper alloy with a composition of 63% nickel and 27% copper, among other elements.

Monel 400 is widely used in Feed water and steam generator tubing.

Monel 400 flanges are constructed of corrosion-resistant and strong nickel-copper superalloy. The material is easy to weld and form well. These flanges are available in different pressure classes, from Class 150 Monel UNS N04400 flanges to Class 2500, and PN6 to PN64.

Yet some alloys like the Monel 400 Flanges can perform well in marine environments because of their chemical composition. With the content of copper ranging between 28% to 34%, it is referred to as a superalloy for its good corrosion resistance properties.

This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength.

Monel K500 fasteners and flanges are virtually non-magnetic and spark resistant, even at temperatures down to -200¡ãF. At temperatures that could rise up to 550C in these mediums, the N06600 Raised Face Weld Neck Flange Ansi B16.5 has been shown to be one of the most resistant out of the other conventional alloys.

MONEL K500 conserva las excelentes propiedades de resistencia a la corrosion de 400, con mayor resistencia y dureza despues del endurecimiento por precipitacion en comparacion con 400.

ASME Sb564 Alloy 400 Plate Flanges Monel 400 N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

Monel 400 Bolts and Nuts are made from a nickel-copper alloy for extreme corrosion resistance, especially in sour conditions. The material is also strong and rigid and can be used to produce bolts and nuts for high temperature service. HT PIPE is a leading manufacturer and supplier of Monel 400 Bolts and Nuts of all sizes and types. Among the ingredients are carbon, aluminum, manganese, silicon, iron, sulfur and 63% nickel and 28% copper. This composition gives the material a high melting point.

The combination of very low corrosion rates in high-velocity sea water and high strength make alloy K-500 pipe bend and elbow particularly suitable for shafts of centrifugal pumps in marine service.