size carbon steel pipe fitting half coupling nipple

For industrial purposes, in pipeline systems, we usually need to change the direction of transmission; regulate the flow of fluids (oil and gas, water, mud); open or close pipelines, etc. Therefore, to accomplish these activities, steel pipe fittings will be applied.

The alloy exhibits excellent resistance to seawater and brine, making it well suited to marine applications.

Stainless steel fittings are made of corrosion-resistant 304 stainless steel for durability and reliability. Suitable for various industrial applications such as vibration, high pressure or corrosive conditions. To improve sealing and reduce wear*, the manufacturer recommends using both Grey Stainless Steel PTFE Thread Sealing Tape and Welded White Seal Plus Multipurpose Fitting Compound.

Stainless steel does not rust because Cr and Fe in it are oxidized to form a dense passive film to prevent further corrosion.
AISI 304 stainless steel has excellent corrosion resistance in mild atmosphere and fresh water, and even the surface will not rust. But it is not resistant to halide (such as chloride, fluoride, etc.) corrosion, because halide easily penetrates the passive film, making stainless steel lose its resistance.

Annealing is a heat treatment process which alters the microstructure of a material to change its mechanical or electrical properties. Typically, in steels, annealing is used to reduce hardness, increase ductility and help eliminate internal stresses.

Monel 400 operates in a wide range of acidic and alkaline environments and has excellent ductility and thermal conductivity. Its properties make it ideal for heavy-duty applications and those requiring a high melting point and toughness in the harshest conditions.

The heated carbon steel is then machined into the forged steel fittings. carbon steel astm a105 fittings is used for ambient- and higher-temperature service in pressure systems.

Hence, materials with low carbon content such as ASTM A105 Fittings are not recommended to be used in those applications which have the need to be constantly exposed to a range temperatures above this value.

It is ideal for food processing, chemical processing, and fluid transportation. The most common uses for stainless steel forged fittings are in food and fluid processing, as well as chemical applications. Stainless Steel 304 is the best choice for forged fittings because of its inherent properties.

Stainless steel 304 is a type of stainless steel that is resistant to corrosion and rusting. Stainless Steel 304 Forged Fittings are used for connecting two pipes or tubes together and can be made from a variety of metals, including copper, brass, aluminum, or stainless steel.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

This nickel alloy has good corrosion resistance, good wear resistance and high strength.

We offer sockets, steel sockets, stainless steel sockets, nickel alloy sockets, copper alloy sockets, duplex steel, carbon steel sockets and alloy steel sockets.

The Inconel Alloy 625 is immune against chloride stress cracking.

For the pipe fittings of small size, such as tee, tee and elbow of socket welding and thread, the shape is relatively complex, so the die forging process should be used.

Forged fittings are used to join, branch, blind or route small diameter piping systems (usually less than 2 inches).

ASTM A105 is also called carbon steel, refers to the carbon content of WC less than 2% iron carbon alloy.

Alloy 400 (UNS N04400) is a nickel-copper alloy with high strength (comparable to structural steel) and toughness.

To recover the inherent corrosion resistance of stainless steel castings. The corrosion resistance of stainless steel decreases after investment casting. The corrosion resistance of stainless steel castings recovered to the optimum state after solution treatment.

The length of the pipe nipple is usually specified by the overall length with threads. It may have a hexagonal section in the center for the wrench to grasp (sometimes referred to as a ¡°hex nipple¡±), or it may simply be made from a short piece of pipe (sometimes referred to as a ¡°barrel nipple¡± or ¡°pipe nipple¡±).

Weldolets are the most popular type of branch fittings, belong to the buttweld fittings family, and are available in a wide range of dimensions.

Carbon Steel A105 Grade all products like flanges, butt weld fittings, forged fittings, outlets, round bar that is Fabricated From High Quality Raw Materials. Carbon Steel A105 products are available in Following Specification, Grade and Sizes.

Our high quality standard pattern 150 lb rated stainless steel threaded pipe fittings are manufactured to the highest standards. All stainless steel pipe fittings are monitored by quality control personnel for strict compliance with applicable standards & specifications.

SS 316 forged pipe fittings are used to bend flow and connect two pipes to each other at different angles. They must be designed in such a way that they do not cause cavitation and excessive pressure loss.

The products offered are appreciated in the market due to the best performance and good quality of the products. These nickel alloy 200 outlet fittings are used in pharmaceutical plants, industrial machinery, chemical plants, oil refineries, textile machinery, sugar plants, fertilizer plants, power and cement industries, petrochemical plants, etc. We also offer 200 custom nickel Olets fitting sizes.

INCOLOY alloy 800 (UNS N08800, W. Nr. 1.4876) is a widely used material for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500¡ãF (816¡ãC).

These alloys possess superior ductility and excellent formability.

According to different varieties and requirements of pipe fittings, forging pipe fittings mainly adopts die forging, free forging and cutting forming processes.

A182-F11 is an American standard pearlitic structure heat-resistant steel forgings, the execution standard: ASTM-A182/A182M-2017.

ASME B16.11 Threadolet is the most popular branch connection: the branch is made by welding the item to the outlet of the run pipe. The ends of a Threadolet are bevelled to facilitate the welding process, and for this reason. Threadolet belongs to the family of butt weld fittings.

We have a comprehensive inventory of nickel alloy forged fittings, socket weld and threaded fittings in all types, sizes, schedules and pressures. HT PIPE specializes in the manufacture of nickel alloy forged fittings that are in high demand in many applications in the naval, chemical processing, marine, petrochemical and refining, and oil and gas markets.