socket weld reducing orifice valve flat face blind cl150 din flange dimensions

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

It has good mechanical properties from subzero temperatures up to about 480C.

A286 (1.4980) bolts, also known as alloy 660 bolts, are a stainless steel alloy containing iron, nickel and chromium. A286 bolts are known for their high strength, creep resistance and oxidation resistance at elevated temperatures, once age hardened. As a result, A286 bolts provide high strength from room temperature to approximately 1300¡ãF (700¡ãC).

The corrosion resistance of Monel alloy K-500 is subtantially equivalent to that of alloy 400 except that, when in the age-hardened condition, alloy K-500 has a greater tendency toward stress-corrosion cracking in some environments.

The levels of molybdenum and copper enable Monel K500 Ring Joint Type Flanges to resist reducing agents and acids. Our wide array of UNS N05500 | Monel K500 Threaded Flanges is utilize in rough oil stills, gas and new water tanks, marine installations and clasp, and concoction preparing gear.

Monel 400 has high strength and toughness over a wide temperature range and excellent resistance to many corrosive environments. The composition is shown in the Table below.

Typical applications for Monel K500 grade rods include those tasks that take advantage of the alloy’s high tensile strength and corrosion resistance. For example, Monel B865 K500 forged bar can be used to make impellers, propeller shafts, pump shafts.

Alloy 400 Pipe Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.

Monel K500(alloy K500), UNS N05500 (QQ-N-286), is a precipitation-hardenable nickel-copper alloy that combines the corrosion resistance of Monel alloy 400 with greater strength (over 2x as strong) and hardness. It also has low permeability and is nonmagnetic to temperatures as low as -150¡ãF (-101¡ãC). This alloy shows the corrosion resistant characteristics of grades such as Alloy 400 but with enhanced strength and hardness after precipitation hardening. However, it can be further strengthened by cold working before the precipitation hardening.

As a corrosion resistant alloy, Monel 400 can withstand high temperature steam environments and fast flowing brackish/seawater, while maintaining excellent resistance to stress corrosion cracking in most fresh waters.

Monel 400 flanges are also available for higher temperatures in reduction environments. While Monel 400 flanges are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 flanges.

The alloy has great mechanical properties at subzero temperatures, and with a melting point of 2370¡ã ¨C 2460¡ã F, products can be used at temperatures up to 1000¡ã C.

The alloy has been used in a variety of applications. It has excellent resistance to rapidly flowing brackish water or seawater. It is particularly resistant to hydrochloric and hydrofluoric acids when they are de-aerated.

A nut is a threaded fastener that can be used with a bolt to secure a virtually unlimited number of parts, objects, and accessories for many types of applications. Monel 500 alloy provides short and long term benefits when used as a material for making nuts. Monel nickel copper k500 nuts provide strength and corrosion resistance in both acidic and alkaline environments. Monel nickel copper k500 nuts are also known for their favorable dimensional accuracy and non-corrosion in salt water and hydrofluoric acid.

Monel 400 and K500 nuts also exhibit excellent corrosion resistance in marine applications and have reasonable corrosion resistance to sulfuric and hydrochloric acids under reducing conditions. A standout feature of monel nuts is their excellent resistance to hydrofluoric acid, a particularly difficult acid to handle, at all concentrations up to the boiling point. For hydrofluoric acid applications, Monel nuts are probably the most corrosion resistant of all commonly used specialty alloys.

Monel 400 flanges are a nickel-copper alloy (approximately 67% Ni ¨C 23% Cu) resistant to seawater and steam at high temperatures, as well as salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold work. This nickel alloy has good corrosion resistance, good weldability and high strength.

Essentially, Monel 500 is an age-hardened version of Monel 400. This means that Monel 500 is harder and more resistant to corrosion than Monel 400. This material can be used in sour gas applications. Monel K500 Studs maintain corrosion resistance even in high velocity seawater. Hence, these applications are in seawater and marine engineering applications as well as in shipbuilding applications.

Monel K500, UNS N05500 (QQ-N-286), is a precipitation hardenable nickel-copper alloy that combines the corrosion resistance of Monel Alloy 400 with higher strength (more than 2x stronger) and hardness.

Monel 400 also resistant to corrosion of neutral solution, water, sea water, atmosphere and organic compounds.

Monel 400 has excellent corrosion resistance in hydrofluoric acid and fluorine gas medium.

A nyloc nut, also referred to as a nylon-insert lock nut, polymer-insert lock nut, or elastic stop nut, is a kind of locknut with a nylon collar that increases friction on the screw thread.

Typical applications for alloy K-500 pipe bend and elbow are pump shafts and impellers; doctor blades and scrapers; oil-well drill collars and instruments; electronic components; springs; and valve trim.

ASTM B564 UNS N04400 Slip on Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

The superposition of residual stress caused by cold working and aging thermal stress, as well as the preferential embrittlement of the surface layer at the initial stage of aging, are the main reasons for aging cracking of Monel K500 alloy.

This alloy is not suitable for highly oxidizing acids such as nitric acid and nitrous acid. It is resistant to sulfuric acid up to 80% and hydrochloric acid solutions up to 20%.

A nut is a fastener that runs through its inner radius. Nuts are used in combination with bolts to hold a virtually unlimited number of parts, objects and accessories for many types of applications. When Monel 400 alloy is used as a material for making nuts, benefits can be seen in the short and long term. Monel Nickel Copper 400 Nuts provide strength and corrosion resistance in both acidic and alkaline environments. Monel NiCu 400 nuts are also known for their favorable dimensional accuracy and non-corrosion in salt water and hydrofluoric acid.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

Alloy 400 has corrosion resistance, high strength and good weldability. Monel 400 has amazing mechanical properties at sub-zero temperatures. It has a melting point of 2370-2460¡ãF and is easily used at temperatures up to 1000¡ãF.

The Curie temperature of this alloy lies within the ambient temperature range and is affected by changes in the alloy’s chemical composition. Caution is recommended in applications requiring strong non-magnetic properties.

Monel 400 has excellent corrosion resistance in hot concentrated alkaline solution.