Special nickel alloy Monel K500 UNS N05500 2.4375 bolt nut washer fasteners

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

Monel alloy K-500 pipe bend and elbow have been found to be resistant to a sour-gas environment. After 6 days of continuous immersion in saturated (3500ppm) hydrogen sulfide solutions at acidic and basic pH’s (ranging from 1.0 to 11.0), U-bend specimens of age-hardened sheet show no cracking.

ASME Sb564 Alloy 400 Plate Flanges Monel 400 N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

ASTM B564 UNS N04400 Slip on Flange A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

The Monel 400 alloy is also known as super alloy monel. This alloy is available in some standard shapes such as hexagon, round, tube, pipe, plate, strip, sheet and wire.

A threaded rod, also known as a stud, is a relatively long rod that is threaded on both ends; the thread may extend along the complete length of the rod. They are designed to be used in tension. Threaded rod in bar stock form is often called all-thread.

Alloy 400 Blind Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Monel bolts, like Monel 400 and K500, are made from a nickel-copper alloy and exhibit high strength, toughness and good corrosion resistance over a wide temperature range.

We are a maker, broker, stockist, provider and exporter of ASME SB564 Monel K500 Flanges which are precipitation solidified, high in quality ribs, yielding a rigidity of 115 ksi for a power pressed execution. Monel K500 fasteners and flanges offer a unique combination of high strength with similar corrosion resistance to Monel 400 and improved resistance to a sour-gas environments.

Monel k500 round bar is an age hardening nickel base alloy. This nickel-based Monel UNS No5500 triangular bar also contains some elemental copper added to its alloy. Copper is known to have good corrosion resistance when added to Monel UNS 5500 spring steel bar, similar to alloy grade 400.

There are different standards to cover the different nominal bore sizes of the flanges. The ANSI B16.5 Monel DIN 2.4360 Blind Flange that has diameters ranging from ? inches to 48 inches in this standard.

Monel K500 fasteners are cold worked prior to precipitation hardening. The strength of the fasteners is stable to 1200 degrees Fahrenheit. Here, at this temperature, it becomes more ductile, reaching toughness around 400 degrees Fahrenheit. Higher strength and hardness after precipitation hardening compared to 400. Due to its numerous advantages, Monel K500 ASTM fasteners are used in a wide range of industries.

Monel 400 also resistant to corrosion of neutral solution, water, sea water, atmosphere and organic compounds.

Monel 400 Pipe Flanges A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

Monel 400 and K500 flanges also exhibit excellent corrosion resistance in marine applications and have reasonable corrosion resistance to sulfuric and hydrochloric acids under reducing conditions.

El material Monel K500 tiene excelentes propiedades mecanicas. Tienen una resistencia a la traccion minima de 140Ksi y un limite elastico minimo de 100Ksi. La aleacion tiene una dureza de 280 Rockwell y se puede estirar facilmente en un 29 %.

Monel 400 or also known as Nickel 400 is a solid solution alloy that is a high strength material that can be used over a wide temperature range. It also has excellent corrosion resistance and has applications in many areas in marine and chemical processing. It is used in applications such as valves, pumps, fresh water tanks and propeller shafts.

Typical applications for alloy K-500 pipe bend and elbow are pump shafts and impellers; doctor blades and scrapers; oil-well drill collars and instruments; electronic components; springs; and valve trim.

Alloy 400/Monel 400 comes directly from refined ore bodies in Canada, and with a copper content of approximately 30 wt%, it provides a lower cost alternative to commercially pure nickel, but still retains a very similar characteristics.

Monel 400 is a popular high performance nickel copper alloy commonly used in critical and high performance applications. Monel 400? has high strength, excellent resistance to acid and alkaline environments, and good ductility and thermal conductivity. This alloy maintains its properties and performance in temperatures ranging from subzero to 1,000¡ãF (538¡ãC). Monel 400 can only be hardened by cold work.

This alloy is most commonly used in a range of environments from mildly oxidizing to neutral and moderately reducing conditions. Other areas of application for this material are marine environments and other non-oxidizing chloride solutions.

Increased performance is obtained by adding aluminum and titanium to a nickel-copper matrix. Flanges are pipe fittings that connect pipes to each other and are used to connect pipe ends. In addition, Monel K-500 flanges can be perfectly matched with various Monel K-500 pipes to ensure the stability and firmness of the connection.

Overcoming the impact of downtime caused by corrosion, stress and extreme temperatures, and the cost impact of failure rates and safety has driven the industry to look for materials like Monel 400, which provide increased reliability in harsh conditions.

At room temperature settings, Monel 400 exhibits slight magnetic behavior, thus, the use of WNR 2.4360 Reducing Flange could also be extended to applications that require magnetic characteristics to a certain degree.

Monel K500 Flat Washers feature aluminum and titanium elements for the excellent corrosion resistance of Alloy 400; improved strength, hardness, erosion resistance and oxidation fatigue resistance. We manufacture all types of Monel K500 machined washers in virtually all shapes and sizes.

We offer W.Nr 2.4360 Monel 400 Male & Female Flanges to the oilfield fabrication, offshore and to petrochemical industries; our flanges are age hardened and are resistant to caustic solutions, seawater, and to chloride solutions and nitric acids, under oxidising and reducing temperatures. HT PIPE takes ultimate pride in offering the above mentioned range of products that fall under the Monel Flanges product type that come in two grades, 400 and K500. Also We offer wide range of Monel ASTM B564 400 Flanges such as Monel 400 Slip On Flanges, Monel K500 Weld Neck Flanges, Monel K500 Socket Weld Flanges, 400 Monel Alloy Blind Flanges, Alloy K500 Orifice Flanges, Monel 400 Spectacle Blind Flanges, Alloy K500 Screwed / Threaded Flanges, Monel Alloy 400 Reducing Flanges, Alloy K500 Ring Type Joint Flanges (RTJ) etc.

Monel 400 is a kind of corrosion resistant alloy with large dosage

Alloy 400 also has excellent corrosion resistance in a variety of media including seawater, hydrofluoric acid, sulfuric acid and alkalis. Used in marine engineering, chemical, hydrocarbon processing equipment and heat exchangers.

In fact, in comparison to nickel, the corrosion resistance properties of UNS N04400 Orifice Flange tend to be much higher than nickel itself.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.