Special nickel alloy Monel K500 UNS N05500 2.4375 full thread stud bolt ASME B18.31.2

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

ALLOY K500,Monel K500 is a Ni-Cu alloy with age-hardening properties imparted by alloying additions of aluminium and titanium. Its basic composition is similar to that of ALLOY400 but the alloying additions make it age hardenable under
controlled conditions of temperature and time

A threaded rod, also known as a stud, is a relatively long rod that is threaded on both ends; the thread may extend along the complete length of the rod. They are designed to be used in tension. Threaded rod in bar stock form is often called all-thread.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

K-500 is characterized by high corrosion resistance and is an ideal alloy for use in marine environments where constant contact with salt water is required.

Monel K500 pipe bend and elbow has excellent mechanical properties from sub-zero temperatures up to about 480C.

Alloy 400 is a solid solution of gold that can only be hardened by cold work.

One of the most important characteristics of Monel 400 is that stress corrosion cracks do not occur in general, and the cutting performance is good. The structure of Monel 400 is single phase solid solution with high strength.

Monel K500 nuts are a result of an age hardening process where aluminum and titanium are added to the nickel-copper base and then precipitated throughout the matrix.

Monel K500 is a Nickel-Copper alloy that is precipitation hardenable, due to the additions of Aluminium and Titanium.

Alloy 400 has corrosion resistance, high strength and good weldability. Monel 400 has amazing mechanical properties at sub-zero temperatures. It has a melting point of 2370-2460¡ãF and is easily used at temperatures up to 1000¡ãF.

MONEL K500 conserva las excelentes propiedades de resistencia a la corrosion de 400, con mayor resistencia y dureza despues del endurecimiento por precipitacion en comparacion con 400.

Monel 400 provide superior quality for different types of mechanical, and general engineering applications.

In applications that involve being used at subzero temperature, the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance

Yet some alloys like the Monel 400 Flanges can perform well in marine environments because of their chemical composition. With the content of copper ranging between 28% to 34%, it is referred to as a superalloy for its good corrosion resistance properties.

Alloy 400 is virtually immune to chloride ion stress corrosion cracking in typical environments.

Alloy 400/Monel 400 comes directly from refined ore bodies in Canada, and with a copper content of approximately 30 wt%, it provides a lower cost alternative to commercially pure nickel, but still retains a very similar characteristics.

In fact, in comparison to nickel, the corrosion resistance properties of UNS N04400 Orifice Flange tend to be much higher than nickel itself.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.

It exhibits excellent weldability and can withstand very large amounts of pressure and weight.

It has high strength and excellent corrosion resistance in various acidic and alkaline environments, especially suitable for reducing conditions. It also has good ductility and thermal conductivity.

Alloy 400 pipe bend and elbow have excellent corrosion resistance together with increased strength and hardness.

Monel K500 nuts will retain their strength to 1200¡ãF and even retain their ductility as low as -400¡ãF.

It is resistant to most alkalis, salts, waters, food products, organic substances and atmospheric conditions at normal and elevated temperatures.

The Alloy K500 Pipe Flanges have 63% nickel with 28% copper and carbon, manganese, silicon, sulfur and iron. The iron component in the monel K500 is much lower than that of monel 400. The Monel UNS N04400 Flanges also come under different standards such as ASTM, ASME, ANSI, DIN and all other international standards with varying dimensions. The dimensions of the flanges determine the pressure classes.

The composition of Monel K500 fasteners includes carbon, 2.3% aluminum, manganese, silicon, iron, sulfur and titanium in addition to nickel and copper. It is this unique composition that gives the material its superior strength, extreme corrosion resistance and ductility. Applications for these fasteners include the offshore petroleum industry, power plant applications, petrochemicals, gas handling units, specialty chemicals, and more.

A finished hex nut, also known as a standard hex nut, has a smaller width across the flats and corners compared to a heavy hex nut. Heavy hex nuts are thicker and heavier in weight. The proof load strength is higher than a standard hex nut. Heavy hex nuts provide increased bearing surface area over finished nuts.

It is not useful in oxidizing acids, such as nitric acid and nitrous.

This alloy is most commonly used in a range of environments from mildly oxidizing to neutral and moderately reducing conditions. Other areas of application for this material are marine environments and other non-oxidizing chloride solutions.

A nut is a fastener that runs through its inner radius. Nuts are used in combination with bolts to hold a virtually unlimited number of parts, objects and accessories for many types of applications. When Monel 400 alloy is used as a material for making nuts, benefits can be seen in the short and long term. Monel Nickel Copper 400 Nuts provide strength and corrosion resistance in both acidic and alkaline environments. Monel NiCu 400 nuts are also known for their favorable dimensional accuracy and non-corrosion in salt water and hydrofluoric acid.

MonelK-500 alloy has a strong aging cracking tendency after large cold deformation. Cracks initiate on the surface and propagate towards the center. There are both transcrystalline and intercrystalline forms.