Special nickel alloy Monel K500 UNS N05500 2.4375 hex bolt DIN931 ISO4014

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Monel alloy K-500 pipe bend and elbow have been found to be resistant to a sour-gas environment. After 6 days of continuous immersion in saturated (3500ppm) hydrogen sulfide solutions at acidic and basic pH’s (ranging from 1.0 to 11.0), U-bend specimens of age-hardened sheet show no cracking.

The superposition of residual stress caused by cold working and aging thermal stress, as well as the preferential embrittlement of the surface layer at the initial stage of aging, are the main reasons for aging cracking of Monel K500 alloy.

ASME Sb564 Alloy 400 Plate Flanges Monel 400 N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

The Alloy K500 Pipe Flanges have 63% nickel with 28% copper and carbon, manganese, silicon, sulfur and iron. The iron component in the monel K500 is much lower than that of monel 400. The Monel UNS N04400 Flanges also come under different standards such as ASTM, ASME, ANSI, DIN and all other international standards with varying dimensions. The dimensions of the flanges determine the pressure classes.

Monel 400 bolts can also be used at higher temperatures. While Monel 400 bolts are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 bolts. Even when cooled to the temperature of liquid hydrogen, Monel 400 will not undergo the ductile to brittle transition that can lead to fracture. This is especially unique compared to most ferrous materials, which are generally stronger but very brittle at extreme low temperatures.

The Monel400 bar is a nickel-copper alloy (about 67% ni-23% Cu) that is resistant to seawater and steam as well as salt and corrosive solutions at high temperatures.

Monel 400 es una aleacion de niquel-cobre resistente a la corrosion en muchos entornos. Consiste en dos solidos cristalinos que forman un nuevo solido.

Yet some alloys like the Monel 400 Flanges can perform well in marine environments because of their chemical composition. With the content of copper ranging between 28% to 34%, it is referred to as a superalloy for its good corrosion resistance properties.

Monel 400 es una de las pocas aleaciones que conserva la resistencia a temperaturas bajo cero, asi que utilicela en estas situaciones.

It combines the corrosion resistance of Monel K-500 but gives the added advantage of extra strength and hardness (as a result of its age hardening ability).

The Asme B16.5 Inconel 600 Flange exhibits good resistance across a broad range of corrosive mediums. The chromium content in the Alloy 600 Flanges gives them better resistance as compared to both Alloy 200 as well as alloy 201 under oxidizing conditions. Also, These Monel K500 Flanges are technologically advanced under the direction of skilled specialists by making use of the premium quality of materials.

The blind flanges are used to close a connection while the slip on flanges are used to adjust a connection position. The ASTM B564 Monel 400 Slip On Flanges allow the seamless pipes to slip onto them so the positioning becomes easy. There are welded flanges as well as threaded flanges.

Monelk500, also known as UNS N05500, has the same corrosion resistance as monel400, but has higher mechanical strength and hardness. It has good corrosion resistance and long-term organizational stability.

Monel K500 bolts offer a unique combination of high strength with similar corrosion resistance to Monel 400 and improved resistance to a sour-gas environments.

Alloy 400 Pipe Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

ASME Sb564 Alloy 400 Plate Flanges Monel 400 N04400 Orifice Flange A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

Monel 400 (also known as alloy 400) is an attractive option for industries where corrosion resistance is of the highest priority.

Monel K500 fasteners and flanges are virtually non-magnetic and spark resistant, even at temperatures down to -200¡ãF. At temperatures that could rise up to 550C in these mediums, the N06600 Raised Face Weld Neck Flange Ansi B16.5 has been shown to be one of the most resistant out of the other conventional alloys.

Monel is particularly resistant to hydrofluoric and hydrochloric acid. It may be slightly magnetic at room temperature. Monel is more resistant to corrosion than nickel under reducing conditions and more resistant than copper when oxidized.

Si bien es un metal muy util, tiene un costo prohibitivo en la mayoria de las aplicaciones. Monel 400 cuesta de 5 a 10 veces mas que el niquel o el cobre normales.

Class 150 Monel 400 RTJ Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Monel k500 round bar is an age hardening nickel base alloy. This nickel-based Monel UNS No5500 triangular bar also contains some elemental copper added to its alloy. Copper is known to have good corrosion resistance when added to Monel UNS 5500 spring steel bar, similar to alloy grade 400.

The Monel 400 alloy is also known as super alloy monel. This alloy is available in some standard shapes such as hexagon, round, tube, pipe, plate, strip, sheet and wire.

Monel 400 products on a project basis is one of our strongest capabilities and is unmatched in our industry.

Monel K500 bolts and nuts are used in a variety of industries due to their high temperature resistance, high corrosion resistance and durability. It is a nickel-copper alloy with a composition of 63% nickel and 27% copper, among other elements. HT PIPE is a leading manufacturer of Monel K500 Bolts and Nuts of all types and sizes. Fastener applications include the offshore petroleum industry, power plant applications, petrochemicals, gas handling units, specialty chemicals, pharmaceuticals, equipment, seawater applications, heat exchangers, condensers, and the pulp and paper industry.

ASTM B564 UNS N04400 Slip on Flange A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

Monel 400 is resistant to both steam and seawater as well as highly caustic solutions such as sulfuric, hydrochloric, and hydrofluoric acids when they are deaerated.

Also known as alloy k500, Monel K500 fasteners and flanges are comprised of a nickel alloy that combines the outstanding corrosion resistance of Monel 400 with increased strength and hardness. Stronger than 400, alloy K500 even retains this strength in corrosive conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.

Monel K500 Spacer Flanges has useful resistance to boiling sulfuric acid up to 40 % concentration, to 60 % concentration at 176 Degree F and in all concentrations to 150 Degree F. Stronger than 400, alloy K500 even retains this strength in corrosive conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas. The exception being that Monel K500 fasteners can be more prone to stress-corrosion cracking in some environments than Monel 400.

Our UNS N05500 Flanges provides resistance to stress-corrosion cracking, crevice corrosion, and pitting. These are accessible to our valuable customers in a different range of diameters, wall thicknesses, and sizes at quite affordable rates.