Special nickel alloy Monel K500 UNS N05500 2.4375 nylon lock nut

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Monel400 is a single-phase solid solution Ni-Cu corrosion-resistant alloy.

The blind flanges are used to close a connection while the slip on flanges are used to adjust a connection position. The ASTM B564 Monel 400 Slip On Flanges allow the seamless pipes to slip onto them so the positioning becomes easy. There are welded flanges as well as threaded flanges.

Alloy 400 is virtually immune to chloride stress corrosion cracking in typical environments. Generally, its corrosion resistance is good in reducing environment, but poor in oxidizing environment.

These flanges are designed to comply with International standards and specifications. Monel R405 offers about the same corrosion resistance as nickel but with higher maximum working pressures and temperatures and at a lower cost due to its superior ability to be machined.

The high pressure rating of Monel flanges means they can be used in high pressure environments.

Monel K500 alloy has excellent corrosion resistance, and has higher strength and hardness than Monel 400. This is due to the addition of elements such as Al and Ti to the alloy, and after a certain heat treatment, there are dispersed intermetallic compounds on the substrate.

Studs are threaded at both ends and the middle screw, either thick or thin.It is generally used in mining machinery, Bridges, automobiles, motorcycles, boiler steel structure, pylon, long-span steel structure and large buildings. A bolt is a screw with a larger diameter or without a head, such as a stud.

Alloy 400 Blind Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

This alloy is not suitable for highly oxidizing acids such as nitric acid and nitrous acid. It is resistant to sulfuric acid up to 80% and hydrochloric acid solutions up to 20%.

Monel K500, UNS N05500 (QQ-N-286), is a precipitation hardenable nickel-copper alloy that combines the corrosion resistance of Monel Alloy 400 with higher strength (more than 2x stronger) and hardness.

Monel K500 nuts will retain their strength to 1200¡ãF and even retain their ductility as low as -400¡ãF.

Monel nuts are often used for standard and advanced applications where high levels of strength and superior corrosion resistance is nearly always required. Monel 500¡¯s premium corrosion resistance, strength and usability in extreme conditions makes it the ideal choice for a wide range of industrial applications.

Monel 400 is a Nickel-Copper alloy, resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.

Monel K500 bolts and nuts are used in a variety of industries due to their high temperature resistance, high corrosion resistance and durability. It is a nickel-copper alloy with a composition of 63% nickel and 27% copper, among other elements.

The combination of very low corrosion rates in high-velocity sea water and high strength make alloy K-500 pipe bend and elbow particularly suitable for shafts of centrifugal pumps in marine service.

This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength.

Monel 400 is a flexible nickel (63% minimum) – copper (34% maximum) alloy retaining strength and toughness at low temperatures while still being effective at temperatures around 1000 degrees F.

Monel 400 has high strength and toughness over a wide temperature range and excellent resistance to many corrosive environments. The composition is shown in the Table below.

Monel 400 flanges are constructed of corrosion-resistant and strong nickel-copper superalloy. The material is easy to weld and form well. These flanges are available in different pressure classes, from Class 150 Monel UNS N04400 flanges to Class 2500, and PN6 to PN64.

Nickel alloys are some of the most useful materials for manufacturing technically superior pipes and tubes for industrial applications. Their inherent properties make them viable for a wide range of uses. Nickel alloys are exceptionally corrosion resistant and can be used in high-temperature environments.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.

As a corrosion resistant alloy, Monel 400 can withstand high temperature steam environments and fast flowing brackish/seawater, while maintaining excellent resistance to stress corrosion cracking in most fresh waters.

Monel 400 also resistant to corrosion of neutral solution, water, sea water, atmosphere and organic compounds.

These are widely used in various application industry. We also offer a wide range of monel 400 / K500 Flanges are available in various size, specification & thickness as per the clients requirements.

Monel K500 is a Nickel-Copper alloy that is precipitation hardenable, due to the additions of Aluminium and Titanium.

Monel K500 has about three times the yield strength and twice the tensile strength of Monel 400, and higher mechanical properties can be obtained by cold working or age hardening. Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.

Monel 400 has excellent corrosion resistance in hot concentrated alkaline solution. Monel 400 also resistant to corrosion of neutral solution, water, sea water, atmosphere and organic compounds.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

This nickel alloy has good corrosion resistance, good wear resistance and high strength.

The alloy can be machined at satisfactory speeds with machine tools commonly used in the industry. Generally, cold drawn or cold drawn stress relief materials are recommended for the best machinability and smoothest finish.