special-shaped flange A182 F11 flange ideally used in pipes

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

In applications where higher working pressures are a prerequisite, the use of seamless pipes is justified. Although stronger than welded pipe, the cost is much higher. In addition, in welded products, there is a greater risk of intergranular corrosion in the heat-affected weld zone. The obvious difference between alloy steel welded pipe and seamless product is the transverse seam along the length of the pipe
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P128

sa335 P5 P5 materials used to make ASTM A335 pipes etc. must meet chemical composition, tensile properties and SA335 P5 hardness requirements. This type of alloy steel pipe is used in applications that require high temperature service. ASTM A335 P5 Pipe Supplier’s Composition, A335 P5 Allowable Stress contains lesser amounts of Nickel and Manganese as they increase the hardness of the pipe.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.36

Chromium Molybdenum Alloy Steel or Chromium Molybdenum, CrMo is an alloy steel used for high temperature and high pressure service. Chromium molybdenum is used in power generation and petrochemical industries for its tensile strength, corrosion resistance and high temperature strength.

ASTM A182 Stainless Steel Flanges are manufactured per ASME B16.5 150#, 300#, 600#, 900#, 1500#, 2500#.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

ASTM A320 Class L7 fasteners are manufactured using high strength materials ideal for the manufacture of fastener product bolts, studs and bolts that can be used in a wide range of high temperatures in bolting applications.

Stainless steel is a versatile alloy is considered to be amongst the most widely used metals across the world.Stainless Steel A403 WP304 contains higher chromium and low carbon content.

The A335 P91 chrome tube composition makes these high mechanical properties possible for the material. P91 steel pipe materials can be normalized and tempered during the production process, and can also be quenched and tempered. These methods increase the strength of the material. Additionally, these pipes are drawn and seamless.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.24

HASTELLOY C-276 alloy (UNS N10276) was the first wrought, nickel-chromiummolybdenum material to alleviate concerns over welding (by virtue of extremely low carbon
and silicon contents).

Nuts with a nominal size over 1 inch shall be a UNC Series Class 2B fit or an 8 UN Series Class 2B fit. High strength ASTM A194 grade 2H nuts are common in the market and are often replaced by ASTM A563 grade DH nuts due to the limited availability of DH nuts in certain diameters and finishes.

ASTM A335 has added chromium and molybdenum elements and has good tensile strength, good high temperature and corrosion resistance.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P92

ASME SA182 F5 pipe flange weight depends on wall thickness and nominal bore. The wall thickness of the flange is determined by the pressure rating.

It is almost the same as AISI 4130 chrome-molybdenum alloy steel, but with a slightly higher carbon content. Compared to AISI/ASTM 4130 alloy steel, AISI 4140 steel has a higher carbon content, which provides higher strength and heat treating capability, but also has limited weldability.

Chrome Moly Alloy A182 F11 Flanges is thus manufactured by regal sales corporation as it is the most reputed and well-known firm in the steel industry.

These ASTM A182 alloy steel F12 flanges are corrosion resistant. ASTM A182 alloy steel F12 flanges also have high dimensional accuracy.

Applications for Alloy Steel A335 P5 EFW Tubing can be seen in petrochemical, oil and gas industrial applications, power plants and other high pressure and high temperature services.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P123

The term “bolting material” as used in this specification covers, rolled, forged or strain hardened bars, bolts, washers, screws, studs and stud bolts.

F5 A182 Pipe Flanges tends to have a fairly high electrical conductivity amongst other wrought alloy steels in the same category. It has a comparatively high base cost and high embodied energy. ASTM A182 is the Standard Specification for Forged Stainless Steel Pipe Flanges and Stainless Steel Forged Fittings.

Each tube of the A335 shall be hydrostatically tested. In addition, each tube shall be inspected using non-destructive testing methods in accordance with prescribed practices.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.21

It can be used with other a335 gr P22 alloy tube types and fittings. SA 335 gr P22 alloy steel pipe has high heat resistance and low thermal expansion. This property of P22 metal tubing makes it suitable for use in the oil and gas industry, power industry, petrochemical industry and refineries where temperatures often fluctuate at high temperatures.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.44

A387 Chrome Molybdenum Steel Sheet Uses & Applications Due to the key properties of the alloy, chrome molybdenum steel sheet is popular in onshore and offshore production facilities in the oil and gas industry. It is also widely used in the energy industry as a key component in power plants. It can be found in boilers and pressure vessels, heat exchangers, flanges, fittings and valves, pipes and pipe supports.

We are committed to supplying high quality A335 alloy tubes to our esteemed customers at the most reasonable price. Following the principles of Total Quality Assurance is our risk. In pursuit of total quality, we have developed a quality specification and quality assurance work plan.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.38

Steel pipes are used in structures, transportation, and manufacturing. They are sized according to their outer diameter, with the inner diameter varying based on wall thickness. Some applications need thicker walls than others, depending on the forces the pipe must manage.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

A182 threaded flanges are primarily used for utility services such as air and water. It is similar to a Slip-On flange, but the holes are threaded.

ASTM A 182 Alloy Steel GR F11 Round bars are generally considered less robust than stainless steel alloys, and their price plays an important role in the purchase.

Its tensile strength is 380 Mpa, while its yield strength is 585 Mpa at 0.2% Offset. The elongation of astm a182 gr f9 is 20 %.

Astm a335 P91 pipe is a seamless pipe for high temperature applications. These pipes are made of ferritic alloy steel. Chemically speaking, a335 P91 welded pipe contains elements such as molybdenum (Mo) and chromium added to the alloy. The tensile strength of sa335 grade P91 pipe increases when molybdenum and chromium are added to the alloy. The tensile strength of a335 grade P91 pipe is 415 Mpa, while its yield strength is 205 Mpa. Pipe elongation ranges from 20% to 30%.

ASTM A182 F11 flange has various dimensions and sizes such as 1/2″ to 36″. This is used in class like 150#, 300#, 600# and many more.

WPHY 52 chemical composition includes metals like Manganese, aluminium, phosphorus, sulphur, vanadium, silicon, nickel, titanium, chromium, molybdenum and copper.A few other moved forward ASTM A860 WPHY 52 properties are its expanded solidness, expanded sturdiness, moved forward weldability, great resistance to hydrogen stretch breaking and its exact measurement.