special-shaped flange A182 F11 flange the flanges F5

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

ASTM A335 Grade P11 is also commonly known as ASME SA335 Grade P11 Pipes, it is a seamless ferritic alloy-steel pipe that mainly has high-temperature applications. The UNS designation for this grade P11 is K11597.

Alloy Steel Flanges are made in different steel alloys. The flanges vary in dimensions and types. There are ? inches through 48 inches of nominal diameter sizes of flanges.

B7 y B7M se trataran termicamente mediante enfriamiento rapido y revenido en un medio liquido. Para los sujetadores B7M, el tratamiento termico final, posiblemente una operacion de templado si se realiza a un minimo de 1150 ¡ãF [620 ¡ãC], debe realizarse despues de todas las operaciones de mecanizado y formacion, incluido el laminado de roscas y cualquier tipo de corte. Preparacion de la superficie que permite realizar pruebas de dureza, evaluacion no destructiva o tension ultrasonica de pernos.

It is a standard specification defining typical chemical composition, mechanical properties, hardness requirement, preferential heat treatment, product marking, certification and other requirements, suitable for bolting used in pressure vessel service, valves, flanges and fittings. ASTM A193 defines both SI (Metric) and inch-pound units.

We are also a supplier and exporter of Alloy Steel ASTM A182 F5 Butt Weld Flanges for high pressure hydraulic systems.

Grade B7 is a heat-treated chromium-molybdenum alloy steel with minimum tensile requirement of 100 ksi, yield of 75 ksi and maximum hardness of 35 HRC.

We can supply chrome molybdenum alloy flanges sorted by alloy grade, size and pressure.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

We offer a variety of ASTM A182 F12 alloy steel round bars to choose from, and these forged bars can be customized according to customer requirements. They are widely used in automotive and other fields due to their excellent quality and unparalleled functionality.

Which means that one has to know if the alloy steel flange material is critical to achieving good weld integrity and the need for proper filler metal selection.High heat resistance steel grades are generally known as Chromium Molybdenum Steel.

Grade P11 is known as chrome molybdenum alloy steel. Compared to carbon steel, the properties of this alloy steel are much higher. Typically, alloy steels such as ASTM A335 P11 pipe tend to have much higher element percentages than conventional steels. So take their efficiency to the next level. The alloy composition of the P11 grade consists of chromium and molybdenum, with a chromium percentage of approximately 1.25. The content of molybdenum in the alloy steel P11 seamless pipe is about 0.5%.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P124

For most applications, INCONEL alloy 718 is specified as: solution annealed and precipitation hardened (precipitation
hardening, age hardening, and precipitation heat treatment are synonymous terms).Good mechanical properties: tensile, fatigue and creep-rupture

Alloy steel pipes and tubing are the best choice for stress corrosion cracking (SSC). These also apply to environments where the problem is pitting and crevice corrosion. These tubes and tubes are available within machining allowances and tolerances.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.34

ASTM A335 P91 Welded Pipe, A335 P91 Pipe Gauge Alloy Steel Pipe is suitable for bending and similar forming operations, as well as fusion welding in high temperature service. We stock ASTM A335 P91 Seamless Pipe (HFS), ASME SA Gr.P91 Pipe and Gas Cylinders in a wide range of sizes with divider thicknesses up to 100mm.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P135

Flange connection has good strength and sealing, simple structure and low cost. It can be repeatedly disassembled.

Chrome moly alloy flanges connect pipes, valves, pumps and other equipment, forming a piping system.

HastelloyC-276 (Hastelloy) is a tungsten-nickel-chromium-molybdenum alloy with extremely low silicon-carbon content and is considered to be an all-around corrosion-resistant aluminum alloy. The key moisture-resistant chlorine, various air-oxidizing fluorides, isopropyl titanate solutions, hydrochloric acid and air-oxidizing salts, have good corrosion resistance in ultra-low temperature and standing temperature sulfuric acid. Therefore, in the past 30 years, it has been widely used in extremely corrosive natural environments such as chemical plants, petrochemicals, flue gas desulfurization, pulp and paper industry, and environmental protection.

Corrosion resistance

The aluminum alloy has the following characteristics: 1. It has good corrosion resistance to most corrosive substances under the two conditions of air oxidation and repair. ¢ÚIt has good resistance to pitting corrosion, void corrosion and intergranular corrosion. The higher content of Mo and Cr makes the aluminum alloy resistant to corrosion by chloride ion content, and the W element further improves the corrosion resistance. At the same time, Hastelloy C-276 aluminum alloy is one of the only types of raw materials that are resistant to wet chlorine, hypochlorite and chlorine dioxide saturated solutions. Ester solution has obvious corrosion resistance. It is one of the very few raw materials that can be used as a hot sulfuric acid saturated solution.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

ASTM A182 F5 flanges are ready for industrial, construction and transportation applications.

We offer a wide range of ASTM A335 P9 alloy steel seamless pipes using high quality raw materials. These alloy steel P9 ERW tubes are forged between 2250¡ãF/1750¡ãF (1230¡ãC/955¡ãC) for 30 minutes per inch of billet or ingot section thickness. These are A335 P9 pipes manufactured to international quality standards. These alloy steel P9 seamless pipes are also available in different sizes, grades, thicknesses and specifications according to customer requirements.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P141

Nickel alloy 20 is a low-carbon, niobium-stabilized austenitic nickel/iron/chromium alloy with additions of molybdenum and copper. ASTM B366 specification covers Inconel, Monel, Hastelloy and Nickel Alloy Pipe Fittings used in acidic and sea water.

Flanges are usually welded or threaded. Flange joints are made by bolting two flanges together with a gasket between them to provide a seal.

ASTM A193 Grade B7 specification covers requirements for high tensile alloy steel bolting material for use in high temperature or high-pressure service and other special purpose applications.

Blind flanges have the face thickness of a flange, a matching face type, and similar bolting pattern.

There are different types and grades of the blind flanges as well. There are other different types of ASME SA 182 AS Pipe Flanges such as the weld neck flanges and socket weld flanges each specified for a particular role

Unlike the bends, the elbows can reduce the pressure applied on the walls when turning the fluid flow direction.Fittings made from WPHY 52 material are known to have a long work life, durable, tough and hard. The WPHY 52 properties make these fittings a perfect cost saving solution for a variety of industries.

We offer ASME SA335 Grade P22 Welded Pipe, ASTM A335 P22 Pipe is manufactured according to ASTM standards. Alloy steel A335 P22 ERW tube, Astm A335 P22 temperature extreme cold formed, made from steel strip drawn through a series of rolls.

Alloy Steel F9 Threaded Flanges is 100% recyclable, where 50% of new steel is produced using re-softened scrap metal rendering it an Eco-friendly material. There are different classes to indicate the pressure capacities of the flanges. The AS A182 F9 RTJ Flanges are a special type of flanges because they come in two parts that have two rings that are welded to the pipe ends first and then the pipes are brought together by welding.

Among alloy steel grades, when metals like Nickel, Chromium and Molybdenum along with other alloying element content consist of less than 10.5% of the total alloy percentage, they are defined as low alloy steels.Generally, most low alloy steel flanges possess a precise chemical composition.

A335 pipe is highly resistant to rupture at high temperature and pressure. Chromium molybdenum tubes with resistance to hydrogen cracking and sulfide stress corrosion cracking are superior to carbon tubes.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.60