stainless steel pipes 304l stainless steel pipe

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

ASME B36.19M is the standard specification for stainless steel pipes, which specifies the dimensions, tolerance, and manufacturing requirements for both welded and seamless pipes.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

304 Piping Spools are made of 304 Stainless Steel, a common and popular material in many industrial applications that require resistance to corrosion and oxidation. These S30400 Piping Spools are prefabricated using specialized machinery and processes, which ensure that they are highly accurate and reliable.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

Inconel 718 is a nickel-chromium-based alloy that is commonly used in high-temperature applications such as aerospace and gas turbines. One of the most important factors in the production of ASTM B670 Inconel 718 Sheet is the plate rolling process. There are two main types of Inconel 718 plates available on the market: hot rolled and cold rolled plates.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

For duplex S31803 nuts, 2 minutes to 3 minutes per mm of wall thickness at temperatures around 1080 degrees Celsius is sufficient to achieve a balanced austenite/ferrite ratio. After annealing, it is recommended to cool these Duplex S32205 nuts as soon as possible.

UNS N08825 Flange Incoloy 825 Flanges are one such type of flanges that have outstanding resistance to oxidizing as well as reducing acids. They are fabricated to improve their resistance to corrosion and are clean to weld

At elevated temperatures the annealed and solution annealed alloy shows good resistance to scaling and has high strength.

ASTM A213 TP 310 Pipe consists of 24% Chromium, 19% Nickel, Sulfur, Phosphorus, Silicon, Manganese and Carbon. Higher chromium and nickel content also makes it superior to 304 or 309 stainless steel. The material also has a minimum yield strength of 205 MPa and a minimum tensile strength of 520 MPa. The elongation is 40%, and the Brinell hardness of the 310 stainless steel pipe is 225HBW.

Hastelloy c22/C276 fasteners have good dimensional accuracy, corrosion resistance, durability, high durability, high flexibility, strong structure, high tensile strength and other characteristics. The presence of molybdenum and tungsten provides good resistance to reducing media. The nickel content of Hastelloy c22 fasteners provides admirable resistance to oxidizing aqueous media. These fasting agents also work well wet in environments containing chlorine, formic acid, and acetic acid.

astelloy B2 Spectacle Blind Flanges, Hastelloy? Alloy B2 Flanges, Hastelloy 2.4816 Weld Neck Flanges Exporter, ASTM B564 Alloy B2 Forged Flanges, ASME SB 564 Alloy B2 Blind Flanges

Steel pipes can be disintegrated on the basis of its application. Typical applications of steel pipes are in the area of water pipelines, industrial water lines, oil pipe lines, cross country pipe line, agriculture and irrigation pipes, tube lines for natural gas, chemical industries, automobile industry, construction industries and other purposes.

ASTM A269 Alloy 254 Seamless Pipe Material is a very high end austenitic stainless steel.

Alloy C276 is a nickel, chromium and molybdenum alloy. Hastelloy C276 is designed for excellent corrosion and oxidation resistance in a variety of environments. These alloys also show resistance to pitting and crevice corrosion.

Bright Annealed (BA) is produced by heat-treating (annealing) steel with a controlled atmosphere furnace. After heat-treatment, the steel has a reflective, mirror-like appearance, but may also have some imperfections and cloudiness. BA stainless steel can be buffed to attain a more reflective finish, and is often specified for applications where a highly reflective surface is desired.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

Duplex-grade stainless steel alloys have ferritic/austenitic properties, giving these materials superior strength and excellent resistance to oxidation.

The LTCS A420 WPL6 Weld Fittings are greatly resistant against the sea water and marine environments with 1/8 inches to 48 inches nominal bore sizes.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

These low-carbon pipes, however, suffers from yield-point runout. The SA 312 TP304 Square Pipe can be easily installed in difficult areas in houses and buildings.

ASTM A234 WPB short radius in accordance with ASME B16.9.Carbon steel pipe fittings manufactured to ASMT A234 are usually furnished in the butt-welding form in accordance with ASME B16.9 or ASME B16.49.

SA 182 Gr F1 Slip on Flanges also known as SO flanges. This is a flange that slides over the pipe and has an internal design that is slightly larger than the pipe.

The welds obtained with 304/304l have good toughness and ductility. Annealing after forging is recommended to maintain maximum corrosion resistance. 304/304L can be forged between 2100¡ã-2350¡ã F.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.34

We are Manufacturers, Supplier and Exporters of Monel K500 Flanges. These Monel R405 flanges are used with stub end or daft which is butt welded to the pipe with the flange loose behind it.

ASTM A234 WPB Elbow is a standard specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel suitable for for Moderate and High Temperature Service.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

Generally speaking, the carbon-free content of carbon steel pipe flanges is lower than that of molten flanges. They don’t oxidize very quickly. They are flat and fairly light in construction, and the fused flanges have excellent mechanical properties. Improper forging methods often result in broad or irregular grains; hardening cracks and forging are taller than cast flanges.

ASTM A694 is a standard specification covering carbon and alloy steel forgings for pipe flanges, fittings, valves, and other parts for high pressure transmission services. The steel meets chemically analyzed standard chemical composition requirements and meets full casting and tensile strength performance requirements.

Inconel 825 Flanges?also resist localized attack and avoid pitting and crevice corrosion.

When it comes to connecting different sections of carbon steel pipes, ASME B16.9 A234 WPB Carbon Steel Pipe Butt Welded Fittings are the go-to solution. These fittings are designed to provide a reliable and secure connection, while also ensuring excellent flow through the system.

Compared with austenitic stainless steel, F51 duplex stainless steel has twice the compressive strength, and compared with 316L and 317L, the designer can reduce its weight.

Alloying steels have added alloying elements such as manganese and nickel. These elements increase the strength, hardness and toughness of metals. Added elements make alloy steels ideal for demanding industrial applications.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.24

Nickel alloys provide high resistance to a wide variety of corrosive agents, oxidation and excellent performance at high temperatures.Certain Nickel Alloys are better for high temperature applications, while others do a better job with corrosion resistance.

The presence of titanium prevents sensitization at the grain boundary.?

ASTM A335 P91 Alloy Steel Pipe and High Pressure Boiler Tube are the two variants available, the range depends on the size, which only depends on the application. Pipe lengths will be hydrostatically tested and non-destructively tested to specification.
volume_up
content_copy

share
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P125

Inconel is a superalloy made of high concentrations of nickel, chromium and molybdenum. Inconel 625 is highly resistant to corrosive and oxidizing media in a variety of environments. These alloys have excellent ductility and excellent formability. They can be welded easily and are resistant to post-weld carburization or graining.