steel reinforcement A350 LF2 steeel bar

Carbon steel pipe is the most common use piping material in different industries served for construction, structural, liquid transmissions for water, oil and gas. Typical carbon steel pipe material grades in API 5L Grade B, X42 to X70, ASTM A106 B, ASTM A53 B, ASTM A252 Grade 3 and ASTM A333 Grade 6 etc.Mineral and slurry pipe is for the line pipe that applied in mining industries. A slurry pipeline is designated to transmit ores (Iron, Coal materials), or the industry mining waste, we called the pipeline as taillings. And generally these steel pipes connected in a long distances. Above materials mixed with water, we call slurry. People will use pumps to transport to the final destination then water will be filtered out. Since slurry contained different materials some with abrasive properties, so the pipe could be coated with 3PE, FBE layers to against from corrosion.
Both carbon steel pipe in seamless or welded could be used for the transmission of the slurry. So there is a wide range of material and standards available options to suit for the special working conditions.

Carbon steel forged fittings and flanges are prevalent and common used in industries, the representative material grade is ASTM A105 and A350 LF2/LF3.

Carbon Steel A105 Grade all products like flanges, butt weld fittings, forged fittings, outlets, round bar that is Fabricated From High Quality Raw Materials. Carbon Steel A105 products are available in Following Specification, Grade and Sizes.

Refer ASME SA105 CS Welding Neck Flange Price List/ Pressure Rating Chart And Carbon Steel A105 WNRF Flanges Manufacturer

Hex bolts are used to fasten two or more parts together to form an assembly either because it cannot be manufactured as a single part or to allow for maintenance and repair disassembly. By definition “A Bolt is a headed and externally threaded mechanical device designed for insertion through holes in assembled parts to mate with a nut and is normally intended to be tightened or released by turning that nut.” When used with a preformed internally threaded (tapped) hole, the hex bolt’s head is turned to tighten, which technically makes it a screw (see our Tech Data section for a discussion regarding the differences between bolts and screws). Hex bolts are also known as: hex head bolts, cap screws, hex cap screws, hex head cap screws, machine bolts, hex machine bolts, hex head machine bolts and, if fully threaded, tap bolts, hex tap bolts and hex head tap bolts. A hex bolt is often differentiated from a hex cap screw by its underhead bearing surface: if it has a circular boss, called a washer face, it’s a hex cap screw¡ªif it doesn’t then it’s a hex bolt.

ASTM A234 is the standard specification for pipe fittings of wrought carbon steel and alloy steel for moderate and high-temperature service. Carbon steel pipe fittings manufactured to ASMT A234 are usually furnished in butt-welding form in accordance with ASME B16.9 or ASME B16.49. There are two carbon steel grades: WPB and WPC, of which ASTM A234 WPB is mostly often used in pipeline industry. The A234 WPB butt-welding pipe fittings include elbows, bends, returns, tees, reducers, end caps, crosses, lap joint stub ends, nipples and couplings.
After forming at an elevated temperature, fittings are cooled to a temperature below the critical range under suitable conditions to prevent injurious defects caused by too rapid cooling, but in no case more rapidly than the cooling rate in still air. Heat treatment temperatures specified are metal (part) temperatures. Heat-treated fittings are to be treated according to paragraph 7 in Specification A960/A960M.

WPB is the most commonly used carbon steel pipe fitting material for medium and high temperature application now, it can be made by steel pipe like ASTM A106 Gr.C or steel plate like ASTM A285 GR.C.

All SA234 WPB Elbow are manufactured in India and produced from strictly European sourced raw material. All ASTM A234 Elbow & Elbow A234 Wpc are manufactured from plate, pressed in two halves with two weld seams.

Our rapid lead times are some of the quickest in the industry so you will never have to worry about hitting your deadlines. A majority of our business originates from the United States and Canada, but we are quickly becoming a global supplier.

ASTM A515 Grade 70 carbon steel is used in chemical boiler plants and in the petrochemical industry. It is resistant even to high temperatures in the field of application.

The ASTM Carbon Steel A105 Blind Flange is the second most used joining method after welding. ASTM A105 Flanges material are used when joints need dismantling. It provides flexibility for maintenance

We are manufacturers, suppliers and exporters of Carbon Steel A105 / A105N Flanges, which, the American Society for testing materials, classifies as a standard that covers forged Carbon-Steel piping parts that also include carbon steel pipe flanges, which are serviceable in pressure systems at room temperatures as well as temperatures higher than it.

ASTM A105 Pipe Flanges are known to deliver exceptional performance and are generally developed for meeting the demands. We offer a broad range of ASTM A105 Carbon Steel Flanges through a worldwide network of stock-keeping branches. These ASTM A105 Carbon Flange is use in various industries

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Monel 400 is a popular nickel-copper alloy commonly used in high performance applications. The alloy has high resistance to acidic and alkaline environments, high strength, good ductility and thermal conductivity. Monel 400 is suitable for use in the subzero to 1,000¡ãF (538¡ãC) temperature range and can only be hardened by cold work.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

Best price on Carbon Steel A350 LF2 Bright Rod with shortest time delivery or Free Sample of Carbon Steel A350 LF2 Hexagonal Rod.

ASTM A350 LF1, LF2 CL1/CL2, LF3 CL1/CL2 flanges are made from an extraordinary combination of elements such as carbon, chromium, silicon, nickel and other unique chemicals used to strengthen the flange.

There are different types of flanges based on the functionality such as the blind flange, slip on flange and orifice flange.ASTM A105 carbon steel can be forged at temperatures in the range of 2200 to 1700 F followed by quenching and tempering or normalizing.

ASTM A106 seamless pressure pipe (also known as ASME SA106 pipe) is commonly used in the construction of oil and gas refineries, power plants, petrochemical plants, boilers, and ships where the piping must transport fluids and gases that exhibit higher temperatures and pressure levels.

a350 lf2 welding neck flange has very good machinability, dependent on condition, and operations such as turning, sawing, milling, broaching, etc. The sa-350 lf2 flange ring type joint is fitted in two parts and will be connected to the piping application with welding. It is a machined from forging, it is typically butt welded to a pipe. The rim has a series of drilled holes that allow the flange to be affixed to another flange with bolts.

Carbon steel forgings, manufactured in accordance with ASTM A105, are generally used for piping applications. These forged carbon steel piping components (including flanges, fittings, and valves, etc) are used for ambient- and higher-temperature service in pressure systems. The A105N, which is designated with a suffix ¡°N¡±, denotes that the A105 forging shall be furnished in normalized condition. If the forgings are used for piping applications of ASME BPVC or ASME B31, the material shall be its identical equivalent of SA-105 or SA-105N. In short, the heat treatment of normalization distinguishes A105N from A105, or SA-105N from SA-105. ASTM A105 Flange is a specification of flanges. The specification can include different grades of stainless steel material made flanges. The flanges are of forged carbon steel and are meant for high temperature services.

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

Carbon steel A350 LF2 flanges have excellent corrosion resistance. Carbon steel A350 LF2 threaded flanges have excellent strength and excellent machinability.

The heated carbon steel is then machined into the forged steel fittings. carbon steel astm a105 fittings is used for ambient- and higher-temperature service in pressure systems.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

ASTM A105 Pipe Flanges are known to deliver exceptional performance and are generally developed for meeting the demands. We offer a broad range of ASTM A105 Carbon Steel Flanges through a worldwide network of stock-keeping branches.

Within this specific category of mild steel is another steel called High Strength Low Alloy Steel, or HSLA for short. Although HSLA screws belong to the mild steel category, it can be noted that HSLA screws also contain other elements in their alloys, such as copper, nickel, vanadium and molybdenum.