Super Duplex 2507 nut provides the exceptional strength and corrosion resistance

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Though it is important to keep in mind that pitting corrosion can be a concern in chloride solutions when oxidizing media is present. In these conditions, the passive (protective) layer of the Duplex 2205 material may be compromised in localized pitting may occur.

The advantage of the dual-phase structure is that it combines the advantages of ferritic alloys (resistance to stress corrosion cracking and high strength) with the advantages of austenitic alloys (ease of manufacture and corrosion resistance). The service temperature of 2205 duplex stainless steel should be limited to below 600¡ãF. Prolonged exposure to high temperatures can make 2205 stainless steel brittle.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.67

Duplex 2205 stainless steel (both ferritic and austenitic) is used extensively in applications that require good corrosion resistance and strength. This grade offers higher resistance to corrosion

Super Duplex 2507 cannot be strengthened by heat treating. Annealing is performed at 1920¡ãF – 2060¡ãF (1049¡ãC – 1127¡ãC), followed by rapid cooling.

The yield strength is also higher, allowing component designers to reduce section size for load-bearing applications.

2507 is a super-duplex (austenitic-ferritic) stainless steel for service in highly corrosive conditions.

The advantage of combining ferritic and austenitic grades is that the resultant metal has a metallurgical structure that consists of two phases and therefore benefits from the properties of both microstructures. These properties make duplex steel highly sought after in heavy industries, like oil and gas nuclear and chemical processing.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Duplex 2205 is the most widely used duplex (ferritic/austenitic) grade of stainless steel. It is used due to its excellent corrosion resistance and high strength.

Super Duplex UNS S32760 Round Rod has many properties and properties due to the elements present in the chemical composition. Due to these characteristics and properties, these super duplex UNS S32760 round bars are used in a large number of industrial applications.

The material for UNS S32760 Stud Bolts is about 10% lighter when compared to grade 316 stainless steel. The Stud Bolt S32760 demonstrates high performance at cryogenic temperature settings as well. Which means that the ASTM A1082 UNS S32760 has good sub-zero notch ductility properties down to a temperature of minus 50¡ãC.

2507 (UNS S32750) is a super duplex stainless steel designed for applications requiring excellent strength and corrosion resistance.

Duplex 2205 fasteners are made from standard duplex materials. The material consists of carbon, manganese, silicon, phosphorus, 21% chromium, 2.5% molybdenum, 4.5% nickel and nitrogen.

UNS31803 has been supplemented by S32205 (F60) which dual conforms to S31803 but has a higher minimum N, MO, NI and Cr which guarantees a better corrosion resistance.

In general, duplex steel S31803 plate can be used as a replacement for the rather expensive stainless steel alloy grade 904L, as 2205 SS plate has similar properties but is less expensive in composition.

Alloy 2507 has 25% chromium, 4% molybdenum, and 7% nickel. This high molybdenum, chromium and nitrogen content results in excellent resistance to chloride pitting and crevice corrosion attack and the duplex structure provides 2507 with exceptional resistance to chloride stress corrosion cracking.

Combining many of the beneficial properties of ferritic and austenitic steels, 2205 is the most widely used duplex grade. Its high chromium and molybdenum conutenut gives stainless steel excellenut corrosion resistance.

The A182 Gr. F51 / S31803 material is a typical duplex stainless steel, which contains approximately 50% ferrite and 50% austenite.

UNS S31803 Bolted Fasteners are used in marine, agricultural, chemical, construction, shipping, aviation, nuclear and industrial equipment.

There are SA 182 F53 S32750 Blind Flanges, socket weld flanges and weld neck flanges in this range of material. The different flanges are used in different applications set ups.

Duplex steels have high resistance to various types of corrosion. Duplex Steel S31803 is an extremely corrosion-resistant, work-hardenable alloy. Duplex steel S31803 butt weld flanges have good high temperature properties.

The Super Duplex 2507 Pipe is made with 25% of chromium, 4% of molybdenum, and 7% of nickel in their composition. As a result, these pipes possess superior corrosion and erosion resistance in various stress-induced environments.

A Super Duplex 2507 Pipe has outstanding resistance to corrosive and oxidative media.

The steel has excellent resistance to chloride stress corrosion cracking, high thermal conductivity and a low coefficient of thermal expansion. The high chromium, molybdenum, and nitrogen levels provide excellent resistance to pitting, crevice, and general corrosion.

Duplex 2205 is a chromium molybdenum blend which combines properties of both ferritic and austenitic steels.

ASTM A182 UNS S32750 Flanges is the most common super duplex grade that has an enhanced pitting and crevice corrosion resistance compared with the ordinary austenitic or duplex types.

The flange a182 f53 can also differ in the face type as flat face, raised face and ring type joint flanges.

Duplex 2205 Tube may at times exhibit magnetic behavior because the microstructure of its alloy contains about 50% ferrite.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.