Super Duplex 2507 Pipe fittings and UNS S32750 Tee

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

This grade, with a tighter specification, is captioned as F60, equating to UNS S32205. Consequently, S32205 can be dual-certified as S31803 but not vice-versa.

ASTM A790 UNS S32205 es un tipo de acero duplex que es una mezcla de diferentes elementos. La composicion del acero SA 790 UNS S32205 es cromo, molibdeno y nitrogeno.

The duplex stainless steel grade alloy UNS S32750 Washer is a thin plate, which is typically produced in a disk -shaped, although sometimes square shaped with a hole i.e. sometimes present in the middle.

The 2205 gasket is known as a duplex stainless steel gasket because it has a combination of ferrite and austenite and can be made into fasteners due to its high corrosion resistance. It has higher corrosion resistance than 316 stainless steel and is also highly resistant to stress corrosion and chloride cracking. 2205 has been determined to be cost effective because it is only 5% nickel and is significantly less expensive than Hastelloy C276 fasteners.

Duplex stainless steel (DSS) is featured with structure of two phases (¦Á and ¦Ã) and has characteristics of both ferritic and austenitic stainless steel. It has good corrosion resistance and high strength. It is alloyed with 18%-28% Cr and 3%-10% Ni in the condition of low C. Some steels also contain the alloy elements such as Mo, Cu, Nb, Ti and N, etc.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Super Duplex is composed of 24% to 26% chromium, 6% to 8% nickel, 3% molybdenum and 1.2% manganese, with the remainder being iron. Trace amounts of carbon, phosphorus, sulfur, silicon, nitrogen, and copper were also found in Super Duplex.

Duplex steels have higher toughness and better weldability. This is how alloy steel is used for industrially available pressure vessels.

Super Duplex UNS S32760 Reducing Flanges have a strengthened microstructure, a result of added Nitrogen, allowing fabrication of thin and low-weight flanges that are easy on the pocket.

S31803 has been supplemented by S32205 (F60) which has a higher minimum Ni Cr and Mo.

ASTM A479 Duplex Steel UNS S32205 Spring Washers have excellent weldability and can be joined by most common welding methods such as metal arc welding, plasma arc welding, submerged arc welding and gas tungsten arc welding. ASME SA 479 Duplex Steel UNS S31803 Square Washer is a ferritic, austenitic 22% chromium, two phase, 3% molybdenum and 5-6% nickel alloy steel.

UNS S32205 Hex Bolts (also known as S31803) are made of high grade duplex 2205 stainless steel. Because this material is composed of at least 22% chromium, 6% nickel, and 3% molybdenum, it can withstand some of the harsh environmental conditions that other metals cannot, such as corrosion, cracking, erosion, pitting, and more. Stainless Duplex 2205 Hex Bolts also provide twice the mechanical strength compared to standard stainless steel.

Duplex 2205 fasteners have high toughness and hardness while also possessing high levels of tensile strength, all as a result of the chromium present in them. However, it can be concluded that dual phase steel fasteners are undeniable; neither deformed nor damaged. This anomaly is much less likely to happen. 2205 Duplex Fasteners consume delicate structures made from ferritic and austenitic stainless steels that are considered part of an alloy, and the end result provides excellent mechanical properties in duplex fasteners.

The yield strength of 2205 is about twice that of austenitic stainless steel. This allows designers to reduce weight and make the alloy more cost-competitive compared to 316L or 317L.

Seamless pipe is not as strong as Duplex SS 2205 welded pipe, but is very dimensionally accurate. Dimensional accuracy is useful in highly sensitive applications where measurement and calculation accuracy is required.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.40

Known for its high impact strength, UNS S32760 exhibits no ductile-brittle transition, but only a slight decrease in impact energy with decreasing temperature.

Usage of Duplex 2507 should be limited to applications below 600¡ã F (316¡ã C). Extended elevated temperature exposure can reduce both the toughness and corrosion resistance of alloy 2507.

Duplex stainless steels are considered resistant to stress corrosion cracking because they are not as resistant to this form of corrosion as ferritic stainless steels.

The ASTM A182 UNS S32750 Slip On Flanges are good to use with seamless pipes.

Preheating of UNS S32750 Super Duplex Fasteners is not necessary except to prevent condensation on cold metal.

Duplex-grade stainless steel alloys have ferritic/austenitic properties, giving these materials superior strength and excellent resistance to oxidation.

ASTM A790 specified 2205 Stainless Steel Pipe ability to resist stress related corrosion cracking.

Duplex steel UNS S31803, UNS S32205 round rods and wires are widely used in chemical, oil and gas, fertilizer and other application industries.

Super Duplex 2507 Lock Washers has excellent corrosion resistance in marine environments.Lock washers are designed to be tightened to a required torque beneath an ordinary fastener. They exert a spring tension that keeps the fastener from vibrating loose. They are often attached to the nut side of the fastener.

Duplex stainless steel has an array of various benefits such as:
Strength:Duplex stainless steels have approximately double the strength of regular austenitic or ferritic stainless steels.
Toughness and ductility:Duplex stainless steels exceed the toughness and ductility of ferritic grades although they are not as touch as austenitic grades.
Corrosion resistance:As with all stainless steels, corrosion resistance depends mostly on the composition of the stainless steel, with chromium, molybdenum and nitrogen content being the most important. Duplex stainless steels are extremely corrosion resistant and even in chloride and sulphide environments, duplex stainless steels exhibit very high resistance to stress corrosion cracking (SCC). SCC is a type of corrosion that takes place when a particular set of factors are present: Tensile stress, corrosive environment and a sufficiently high temperature.
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Duplex UNS S32205 fasteners are widely used in construction and other industrial applications. We offer these types of fasteners in differenut thicknesses and tolerance limits for a variety of industrial applications.

This is the main reason why Super Duplex Flanges note an improvement of tensile strength over ferritic and austenitic steel grades.

Duplex steel UNS S31803 round bar is widely used for ferritic and austenitic duplex stainless steel bars.

In general, duplex steel S31803 plate can be used as a replacement for the rather expensive stainless steel alloy grade 904L, as 2205 SS plate has similar properties but is less expensive in composition.

Alloy 2205 duplex stainless steel is an alloy developed from the initial Super Duplex Stainless Steel. It is supplied in the solution annealed condition.

Although when the 2205 duplex stainless tubing material has been exposed to temperatures above 572¡ãF, even when the exposure is for a short period of time, the duplex 2205 seamless tube is subject to embrittlement.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”