super duplex 2507 uns s32750 pipes

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Inconel 718 is a nickel-chromium-based alloy that is commonly used in high-temperature applications such as aerospace and gas turbines. One of the most important factors in the production of ASTM B670 Inconel 718 Sheet is the plate rolling process. There are two main types of Inconel 718 plates available on the market: hot rolled and cold rolled plates.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

304 Piping Spools are made of 304 Stainless Steel, a common and popular material in many industrial applications that require resistance to corrosion and oxidation. These S30400 Piping Spools are prefabricated using specialized machinery and processes, which ensure that they are highly accurate and reliable.

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

Stainless Steel 304 Pipe Fittings are made up of 18/8 chromium nickel alloy steels. The SS 304 Elbow has 18% chromium and 8%nickel in its composition. This makes the SS UNS S30400 Buttweld Fitting to be stronger with 215MPa minimum yield strength and 505MPa minimum tensile strength. The combination makes Stainless Steel 304 Buttweld Pipe Fittings corrosion resistant and high temperature capable up to 889 degrees Celsius.

Inconel Alloy 600 is designated as UNS N06600 and Werkstoff Number 2.4816.

A flange is a ring of steel (forged, cut from plate, or rolled) designed to connect sections of pipe, or to join pipe to a pressure vessel, valve, pump or other integral flanged assembly. Flanges are joined to each other by bolts, and to the piping system by welding or threading (or loose when stub ends are used). Stainless steel flange simplified as SS flange, it refers to the flanges that made of stainless steel. Common material standards and Grades are ASTM A182 Grade F304/L and F316/L, with pressure ratings from Class 150, 300, 600 etc and to 2500. It used in more industries than carbon steel as stainless steel has better resistant performances on corrosion environment and always provides with a good appearance.

A105,this material has carbon, manganese, phosphorus, sulfur, silicon, copper, nickel, chromium, molybdenum and vanadium in its composition. Since the other materials are less than 1% of the composition, these are called the carbon steels.

Incoloy 926 (N08926) nickel-based alloy contains 14.0-18.0% Cr and 24.0-26.0% Ni. It is a nickel-based alloy containing titanium and aluminum, with enough chromium to form and maintain a sufficient scale of chromium oxide to protect it under high temperature conditions.

C276 has good fabricability and impressive corrosion resistance in some of the most severe environments.

Alloy 400 (UNS N04400) is a nickel copper alloy with high strength (comparable to structural steel) and toughness. Alloy 400 also has excellent corrosion resistance in a range of media including seawater, hydrofluoric acid, sulphuric acid and alkalis.

Since Type 316 stainless steel alloy contains molybdenum bearings, it has higher chemical resistance than Type 304. Model 316 is durable, easy to manufacture, clean, weld and polish.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.45

This alloy is resistant to the formation of grain boundary precipitates in the weld heat-affected zone, thus making it suitable for most chemical process applications in an as welded condition.

Monel K500 is a nickel-copper alloy that combines the excellent corrosion resistance of Monel 400 (link) with the added benefits of higher strength and hardness. Performance can be improved by adding aluminum and titanium to the nickel-copper matrix and by heating under controlled conditions to precipitate submicroscopic particles of Ni3 (Ti, Al) throughout the matrix. This is commonly referred to as age hardening or aging.

SME B16.47 317L Pipe Flange hardenability will be reduced if constant feeds and low speeds are used. 317L Stainless steel Flanges can be welded using fusion and resistance methods. In Grade 317 Stainless Steel Pipe flange oxyacetylene welding method is not preferred for this alloy. ASTM A182 SS 317L Slip On Flange does not react to heat treatment. A182 F317/F317L Flange can be hardened by cold working.

A335 grade p11 pipe is a seamless ferritic alloy based stainless steel pipe. The tube is a chrome molybdenum alloy. The presence of these two elements in the SA335 p11 pipe increases its mechanical properties.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.46

We are one of the top producers of SA105N Reducing Weld Neck Flange, and our previous clients are always satisfied with our products due to their high-quality and reasonable pricing.

Type 316 stainless steel is manufactured into another grade due to its wide range of potential and is distinguished by the use of the letter “L” in its name. L represents the low carbon content in the steel.

Alloy C276 is a Ni-Cr-Mo alloy containing W and very low carbon and Si content.

Monel 400 flanges are constructed of corrosion-resistant and strong nickel-copper superalloy. The material is easy to weld and form well. These flanges are available in different pressure classes, from Class 150 Monel UNS N04400 flanges to Class 2500, and PN6 to PN64.

Inconel 625 Bolts were developed in the 1960s as a vapor-lined piping material to provide high strength even in extreme high temperatures ranging from freezing low temperatures to 1800¡ãF. Inconel 625 Bolts, also known as Alloy 625, are known for their amazing ability to maintain strength and heat resistance in and out of corrosive environments.

It is an austenitic stainless steel alloy with high nickel (24%), chromium (22%), molybdenum (6%), and nitrogen (0.18%) content and is commonly known as superaustenitic stainless steel (alloys such as 254 SMO (UNS?S31254) and 904L (UNS?N08904) also fall under the superaustenitic designation) while 2205 (UNS S32305/ S31803) and 2507 (UNS S32750) are duplex and super duplex stainless steel, respectively.

Inconel 625 round bars can be manufactured in hot-worked bar form per ASTM B446 specification. These properties specified by ASTM B446 for 2.4856 Inconel 625 hexagonal bar include the tensile strength, yield strength and elongation properties of the material.

ASTM A105, also known as carbon steel, is an iron-carbon alloy with an internal carbon content of nearly 2 percent.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

ASTM A335 P22 Seamless Pipe can be used in forming operations without cracking. This tube can be bent, forged, flanged and fusion welded. It also has very high tensile strength, corrosion resistance and yield strength.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.41

A flange is a ring of steel (forged, cut from plate, or rolled) designed to connect sections of pipe, or to join pipe to a pressure vessel, valve, pump or other integral flanged assembly. Flanges are joined to each other by bolts, and to the piping system by welding or threading (or loose when stub ends are used). Stainless steel flange simplified as SS flange, it refers to the flanges that made of stainless steel. Common material standards and Grades are ASTM A182 Grade F304/L and F316/L, with pressure ratings from Class 150, 300, 600 etc and to 2500. It used in more industries than carbon steel as stainless steel has better resistant performances on corrosion environment and always provides with a good appearance.

321 Stainless Steel Square Bar It can be categorically said that rebar is one of the core components of any manufacturing industry or any industry that relies on machinery. Widely used in automotive, textile, manufacturing, construction, cement, shipbuilding, paper and pulp, defense, heavy earthmoving equipment or aerospace.

Monel K500 Spacer Flanges has useful resistance to boiling sulfuric acid up to 40 % concentration, to 60 % concentration at 176 Degree F and in all concentrations to 150 Degree F. Stronger than 400, alloy K500 even retains this strength in corrosive conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas. The exception being that Monel K500 fasteners can be more prone to stress-corrosion cracking in some environments than Monel 400.

It is suitable for temperatures up to 1000¡ãF (538¡ãC). Alloy 400 has excellent resistance to cavitation and erosion in fast-flowing brackish or seawater.

Stainless steel needs to be cold worked to generate higher tensile strength. Type 304 has slightly lower strength than 302 due to its lower carbon content. Stainless Steel 304 Pipes and Tubes Available are following Specification, Grades and Size.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

800H can resist corrosion of many corrosive media. Its high nickel content makes it resistant to stress corrosion cracking in aqueous corrosion conditions. The high chromium content provides better resistance to pitting and crevice corrosion cracking. The alloy has good corrosion resistance to nitric acid and organic acids, but limited corrosion resistance in sulfuric acid and hydrochloric acid. Good corrosion resistance in oxidizing and non-oxidizing salts, in addition to the potential for pitting corrosion in halides. It also has good corrosion resistance in water, steam and mixtures of steam, air and carbon dioxide.

The strength of Inconel 625 lies not only in its nickel-chromium base but also the hardening mechanism of niobium and molybdenum.

Little or no corrosion occurs in dry gases such as chlorine or hydrogen chloride at room temperature and high temperature. At temperatures up to 550C in these media, this alloy has proven to be one of the most corrosion resistant common alloys.