sus 304 pipe forging

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

Inconel 718 is a nickel-chromium-based alloy that is commonly used in high-temperature applications such as aerospace and gas turbines. One of the most important factors in the production of ASTM B670 Inconel 718 Sheet is the plate rolling process. There are two main types of Inconel 718 plates available on the market: hot rolled and cold rolled plates.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

304 Piping Spools are made of 304 Stainless Steel, a common and popular material in many industrial applications that require resistance to corrosion and oxidation. These S30400 Piping Spools are prefabricated using specialized machinery and processes, which ensure that they are highly accurate and reliable.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

ASME B36.19M is the standard specification for stainless steel pipes, which specifies the dimensions, tolerance, and manufacturing requirements for both welded and seamless pipes.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

One exception, however, are strongly oxidizing acids such as nitric acid. Alloys that contain molybdenum generally do not perform as well in these environments.?

The main difference between carbon steel A350LF2 ferrule flanges and other austenitic steels is the higher hardness of carbon steel alloys.

Alloy 317L can be easily welded and processed by standard shop fabrication practices.?

316 stainless steel pipe bend has very low responsiveness to magnetic fields. Unlike basic stainless steels, which are ferromagnetic, most stainless steel varieties (including 316) are austenitic ¡ª or effectively nonmagnetic.

B564 601 Spade Flange Inconel 601 Flanges are made up of a nickel chromium alloy. The material grads range differently with the composition ratio. The 601 grade has 58% nickel, 21% chromium, carbon, manganese, silicon, sulfur, copper and iron in the composition. There are different types such as socket weld flanges, welded neck flanges, Inconel 601 Slip On Flanges, orifice flanges and so on. The flanges made of this material are strong, corrosion resistant to acids, reducing agents and oxidation and are also harder.

254 SMo UNS S31254 super austenitic steel combines moderate tensile strength with high ductility for excellent corrosion resistance in seawater and various industrial environments. SMO 254 washer is effective against pitting, crevice corrosion and chloride stress corrosion cracking. 254 SMO washer is known for high ductility and good impact strength.

The carbon steel seamless pipe fittings, buttwelded fitting and fabricated ones are available in the market.

Within this specific category of mild steel is another steel called High Strength Low Alloy Steel, or HSLA for short. Although HSLA screws belong to the mild steel category, it can be noted that HSLA screws also contain other elements in their alloys, such as copper, nickel, vanadium and molybdenum.

Alloy steel F12 bar offers some great properties such as strong construction, all-around durability, a wide range of sizes to choose from, and more.

Stainless steel pipes are long, hollow tubes that are used for a wide range of industrial applications. They are produced by two distinct methods which result in either a welded or seamless pipe. Alloy 304 stainless steel pipe provides enhanced strength and corrosion resistance and can be used for all types of fabrication processes, especially those that are subjected to outdoor environmental conditions.

One tension test shall be made for each heat of ASTM A182 F51 flanges. One set of three Charpy V-notch tests shall be performed for each heat of products.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

These grades are excellent for fixed service simple flange connections, but slightly less so when forming a complex metallic shape. Fortunately, the workability of duplex into complex and rounded structures is less of an issue in structural steel given the wide preference for simple mild steel in non corrosive applications.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

This is called as the “center to face” distance and is equivalent to the radius through which the ASTM A234 gr WPB elbow is bent.

MonelK-500 alloy has a strong aging cracking tendency after large cold deformation. Cracks initiate on the surface and propagate towards the center. There are both transcrystalline and intercrystalline forms.

There are the pressure grade ASTM A234 WPB Pipe Fittings in ? inches to 24 inches nominal bore sizes with different wall thicknesses that correspond to the schedules.It does not cover cast welding fittings which refered standards are ASTM A216/A216M and A217/217M.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

ASTM A240 is the standard specification for chromium and chromium-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications.

Type 316/ 316L/316H are austenitic stainless steel intended for use in applications that require high strength, toughness and workability, as well as enhanced corrosion resistance.

The duplex F51 flanges can be provided in a variety of flange types such as welding neck, slip on, blind, plate, threaded, socket welding, long weld neck, spectacle blind, spade, spacer, and orifice, etc.

The chemical composition of Monel K500 Nippo Flanges provides great resistance to a lot of corrosive environments, such as pitting, crevice corrosion, inter ¨C granular corrosion, and stress ¨C corrosion cracking. Monel K500 Spacer Flanges has useful resistance to boiling sulfuric acid up to 40 % concentration, to 60 % concentration at 176 Degree F and in all concentrations to 150 Degree F.

Nickel alloy 718 hex bolts and other fasteners are available in lengths from 3mm to 200mm. Hex bolts are used for easy reinforcement because the hex head can handle high torque values when tightening.

Alloy 904L (UNS N08904) is a super austenitic stainless steel designed to provide moderate to high corrosion resistance in a variety of process environments. The combination of high chromium and nickel content, with the addition of molybdenum and copper, ensures good corrosion resistance.

The ANSI A105 Flanges Reducing is basically used for reducing the line size where space limitations will not allow the length of a ASTM A105N Weld Neck Flanges and reducer combination.

Stainless steel round bar is a cylindrical stainless steel product, which is widely used in auto parts, aviation, aerospace hardware tools, chemical industry and other industries. Stainless steel WNR 1.4301 wire is known for its amazing tensile strength and fabric power and is available in a variety of sizes according to customer requirements. They are the product of the best materials and primary strategies that conform to the established norms of the industry. In our assortment we have round rods with special type of ends to ensure short and tight fittings in pipes.

What distinguishes the Hastelloy B3 fastener from its predecessor is its excellent ductility during transient exposure to intermediate temperatures (i.e. machining, heat treatment) due to its lower carbon content. This nickel-molybdenum alloy is typically available in bar, wire, sheet and plate form. Hastelloy B-3 fasteners are commonly used in vacuum furnaces and petro/chemical production lines.

Super Duplex S32760 Bar proves to be an excellent replacement for austenitic grades in marine environments. Super Duplex S32760 round bar (ASTM A276/ ASTM A479) exhibits good heat resistance up to 300¡ã.

Both sulfuric acid as well as hydrofluoric acid are highly corrosive solutions and can easily corrode metals, without good resistance to reductive agents.

It is mainly used for welded pressure vessels where improved notch toughness is required.