tee pipe fitting connector

For industrial purposes, in pipeline systems, we usually need to change the direction of transmission; regulate the flow of fluids (oil and gas, water, mud); open or close pipelines, etc. Therefore, to accomplish these activities, steel pipe fittings will be applied.

With the specification acting as a guide, it is required that the material follow some requirements. Along with the tensile and yield strength, the ASTM A105 Elbow must adhere to the requirements of the specification for details such as reduction of area, elongation, and hardness requirements.

ASTM A182 Alloy Steel Forged Fittings are manufactured according to the ASTM A182 specification, which covers high pressure and high temperature service flanges covered by ASME B16.11, MSS-SP-79/ 83/ 95/ 97 and BS3799 standards.

To recover the inherent corrosion resistance of stainless steel castings. The corrosion resistance of stainless steel decreases after investment casting. The corrosion resistance of stainless steel castings recovered to the optimum state after solution treatment.

Outlet fittings are forged products with high strength and clear cost advantages over conventional pipe branching techniques.

For instance, the use of Carbon Steel ASTM A105 Fittings is prominent in those applications that involved not only environments where the temperatures are high, but also in those applications at room temperature.

SS 316H Forged Tee is a short pipe with a transverse connection at right angles to the pipe. Mostly used to connect multiple pipes to one pipe with two outlets. Usually, they contain an entry. The SS 316 Forged Cross is used to combine or distribute flow by connecting pipes at cross joints and splitting the flow from each pipe.

A105 shall be subjected to heat treatment (annealing, normalizing, tempering, or quenching). A105 shall conform to carbon, manganese, phosphorus, sulfur, silicon, copper, nickel, chromium, molybdenum and vanadium contents.

Steel pipe elbows are important components in plumbing piping systems for changing the direction of fluid.

ASTM A182 refers to low-alloy steel forgings. It belongs to carbon steel.

Steel tee is a T-shaped pipe fittings that has three branches, normally has two forms with Equal Tee and Reducing Tee (Tee reducer), both are used to divide (combine) the pipelines to adjust the flow rate and change the direction.

Hastelloy C276 bushings are widely used in the harshest environments such as chemical processing, pollution control, pulp and paper, industrial and municipal waste treatment, and recovery of sour natural gas.

Coupling is a kind of fittings commonly used in industrial pipe connection.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

The alloy also exhibits resistance to physical deterioration, e.g. – surface pitting and cracking.

This alloy is most commonly used in a range of environments from mildly oxidizing to neutral and moderately reducing conditions. Other areas of application for this material are marine environments and other non-oxidizing chloride solutions.

A182-F11 has good process performance and welding performance, and high durable strength at 500 ~ 550¡æ.

These ASTM A182 alloy steel F5 F9 F11 F12 F22 F91 pipe fittings are corrosion resistant. ASTM A182 alloy steel F5 F9 F11 F12 F22 F91 fittings also have high dimensional accuracy.

The inclusion of chromium in combination with nickel in its chemistry makes it resilient to chemical and environmental corrosion.

Pipe Fittings are usually socket welded or threaded. The high chromium content gives these forgings fittings very good resistance to moisture erosion

Stainless steel fittings are made of corrosion-resistant 304 stainless steel for durability and reliability. Suitable for various industrial applications such as vibration, high pressure or corrosive conditions. To improve sealing and reduce wear*, the manufacturer recommends using both Grey Stainless Steel PTFE Thread Sealing Tape and Welded White Seal Plus Multipurpose Fitting Compound.

Annealing is a heat treatment process mainly used to increase the ductility and reduce the hardness of the material. This change in hardness and ductility is the result of the reduction of dislocations in the crystal structure of the annealed material. Annealing is usually done after the material has undergone a hardening or cold working process to prevent its brittle failure or to make it easier to handle later.

A stainless steel 304 short radius elbow has a radius that is longer than the outside diameter of the pipe it is installed on. These accessories fall under ASTM A403 specification. Their nominal diameters range from 1/8″ to 48″. The standards for these dimensions are ASME B16.9 and B16.28. 304 stainless steel 90 degree elbows are commonly used elbows.

Incoloy 800 is a popular choice in the oil and gas industries because it can withstand sour gas and high chloride environments.

Being a trailer product, threadolets are designed for specific conditions based on Process piping Code ASME B31.3, hence, Dimension is also specified by the designer. However, MSS-SP-97 provide dimension requirements for standard 90¡ã self-reinforced branch connection with butt, socket and threaded end types

Nickel alloy pipe fittings are composed of alloys with nickel as the main element. There is complete solid solubility between nickel and copper. Its wide resolution range between iron, chromium and nickel enables many alloy combinations.

SS 304 Forged Tee provides better mechanical properties for connecting pipes to mains. A tee consists of an inlet and two outlets placed at right angles to each other. SS 304 Forged Cross is used where four pipes intersect. They either divide the process or merge the process.

Typical applications of Inconel 800 include the food and beverage industry, in addition to being used for heat treatment components.

The emphasis of this alloy is placed on the fact that it is more resistant to aggressive forms of corrosion. In particular, Incoloy 800 shows very high resistance to corrosive compounds seen in aqueous environments.

90 degree elbow with female National Pipe Taper (NPT) threads for changing the direction of flow between two pipes. Our high quality standard Class 150 stainless steel threaded fittings are manufactured to the highest standards.

The length of the pipe nipple is usually specified by the overall length with threads. It may have a hexagonal section in the center for the wrench to grasp (sometimes referred to as a ¡°hex nipple¡±), or it may simply be made from a short piece of pipe (sometimes referred to as a ¡°barrel nipple¡± or ¡°pipe nipple¡±).