UNS N04400 pipe bend combined with excellent resistance to stress-corrosion cracking in most freshwaters

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Monel 400 and K500 flanges also exhibit excellent corrosion resistance in marine applications and have reasonable corrosion resistance to sulfuric and hydrochloric acids under reducing conditions.

Monel K500 nuts are a result of an age hardening process where aluminum and titanium are added to the nickel-copper base and then precipitated throughout the matrix.

Monel K500, UNS N05500 (QQ-N-286), is a precipitation hardenable nickel-copper alloy that combines the corrosion resistance of Monel Alloy 400 with higher strength (more than 2x stronger) and hardness.

The high-temperature plasticity of the experimental alloy added with trace amounts of Mg, Cr and Co is obviously improved, and it exhibits certain superplasticity. At 1010¡æ, the strain rate sensitivity index m is 0.32, and the maximum elongation is 240%.

Monel 400 is a flexible nickel (63% minimum) – copper (34% maximum) alloy retaining strength and toughness at low temperatures while still being effective at temperatures around 1000 degrees F.

Stronger than 400, alloy K500 washer even retains this strength in corrosive. conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.

Alloy 400 has corrosion resistance, high strength and good weldability. Monel 400 has amazing mechanical properties at sub-zero temperatures. It has a melting point of 2370-2460¡ãF and is easily used at temperatures up to 1000¡ãF.

Alloy 400 is low in strength in the annealed condition so, a variety of tempers may be used to increase the strength.

MONEL K500 is a age-hardenable Nickel-Copper alloy which combines the corrosion resistance of Alloy 400 with high strength corrosion fatigue and erosion resistance.

Although ASTM B165 UNS N04400 material has lower strength in the annealed condition, it exhibits excellent mechanical properties even at sub-zero temperatures. Monel tubes can be used up to 1000 degrees Fahrenheit. In order to improve the mechanical properties of Monel 400 welded pipe, it is possible to make finished products on it.

A threaded rod, also known as a stud, is a relatively long rod that is threaded on both ends; the thread may extend along the complete length of the rod. They are designed to be used in tension. Threaded rod in bar stock form is often called all-thread.

Known for their improved workability under cryogenic temperatures, with a rigidity of 160 ksi and a superb dimensional security are variables that add to the unwavering quality of UNS N05500 Monel K500 Socket Weld Flanges. The ASTM B564 Monel 400 Lap Joint Flanges and other flanges can also come as threaded, forged, screwed or plate flange types.

Valued for its high strength and corrosion-resistant properties, Monel 400 is available from Continental Steel in multiple forms for use in a variety of end uses.

Monel Alloy K500 Flanges are manufactured under the supervision of our experienced professionals.

Monel 400 contains the same levels of nickel and copper as the natural nickel ore found.

These products are manufactured with the latest technologies using high grade raw materials. We are manufacturer in national & international standards.

Monel 400 is a popular nickel-copper alloy commonly used in high performance applications. The alloy has high resistance to acidic and alkaline environments, high strength, good ductility and thermal conductivity. Monel 400® is suitable for use in the subzero to 1,000°F (538°C) temperature range and can only be hardened by cold work.

Monel K500(alloy K500), UNS N05500 (QQ-N-286), is a precipitation-hardenable nickel-copper alloy that combines the corrosion resistance of Monel alloy 400 with greater strength (over 2x as strong) and hardness. It also has low permeability and is nonmagnetic to temperatures as low as -150¡ãF (-101¡ãC). This alloy shows the corrosion resistant characteristics of grades such as Alloy 400 but with enhanced strength and hardness after precipitation hardening. However, it can be further strengthened by cold working before the precipitation hardening.

Monel K500 fasteners and flanges are virtually non-magnetic and spark resistant, even at temperatures down to -200¡ãF. At temperatures that could rise up to 550C in these mediums, the N06600 Raised Face Weld Neck Flange Ansi B16.5 has been shown to be one of the most resistant out of the other conventional alloys.

Monel K500 (alloy K500), UNS N05500 (QQ-N-286), is a precipitation-hardenable nickel-copper alloy that combines the corrosion resistance of Monel alloy 400 with greater strength (over 2x as strong) and hardness. It also has low permeability and is nonmagnetic to temperatures as low as -150¡ãF (-101¡ãC).

Alloy 400 Seamless Tubing has good ductility which helps to shape and form easily & are available in flat oval, elliptical, round, rectangular & square shapes with 0.030 in. to 1.250 in. OD, 0.008 in. ID & 0.003 in. to 0.280 in. wall thickness.

Generally, the corrosion resistance of Monel K500 in solid solution is basically the same as that of Monel 400 alloy, so the corrosion resistance data of Monel 400 can be applied to Monel K500 alloy. Due to its low corrosion rate and high strength in flowing seawater, the alloy is particularly suitable for manufacturing seawater corrosion-resistant centrifugal pump shafts.

Alloy 400 is a solid solution of gold that can only be hardened by cold work.

MONEL Alloy K-500 (UNS N05500 / W.Nr. 2.4375) is a nickel-copper alloy that combines the excellent corrosion resistance of MONEL Alloy 400 with the added benefits of higher strength and hardness.

ASTM B564 UNS N04400 Pipe Flange Monel 400 has a wonderful corrosion resistance by many reducing media such as sulfuric and hydrochloric acids.

Astm B564 Monel 400 Blind Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

The corrosion resistance of Monel alloy K-500 is subtantially equivalent to that of alloy 400 except that, when in the age-hardened condition, alloy K-500 has a greater tendency toward stress-corrosion cracking in some environments.

Una aleacion de niquel-cobre con alta resistencia y excelente resistencia a la corrosion en una variedad de ambientes acidos y alcalinos, especialmente para condiciones reductoras. Tambien tiene buena ductilidad y conductividad termica.

Class 150 Uns N05500 Socket Weld Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Las aplicaciones tipicas de la alta resistencia y resistencia a la corrosion de MONEL K500 son ejes de bombas, impulsores, ejes de helices, componentes de valvulas para barcos y torres de perforacion en alta mar, pernos, collares de pozos de petroleo y componentes de instrumentacion para la produccion de petroleo y gas.