316 stainless steel pipe with 400 grit finish

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Inconel 718 is a nickel-chromium-based alloy that is commonly used in high-temperature applications such as aerospace and gas turbines. One of the most important factors in the production of ASTM B670 Inconel 718 Sheet is the plate rolling process. There are two main types of Inconel 718 plates available on the market: hot rolled and cold rolled plates.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

ASME B36.19M is the standard specification for stainless steel pipes, which specifies the dimensions, tolerance, and manufacturing requirements for both welded and seamless pipes.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) >40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

A flange is a ring of steel (forged, cut from plate, or rolled) designed to connect sections of pipe, or to join pipe to a pressure vessel, valve, pump or other integral flanged assembly. Flanges are joined to each other by bolts, and to the piping system by welding or threading (or loose when stub ends are used). Stainless steel flange simplified as SS flange, it refers to the flanges that made of stainless steel. Common material standards and Grades are ASTM A182 Grade F304/L and F316/L, with pressure ratings from Class 150, 300, 600 etc and to 2500. It used in more industries than carbon steel as stainless steel has better resistant performances on corrosion environment and always provides with a good appearance.

The carbon content of 254SMO is very low, which means that there is very little danger of carbide precipitation caused by heating. It can pass the Strauss intergranular corrosion test (Strauss Test ASTMA262 order E) even after one hour of sensitization at 600-1000¡ãC. However, due to the high alloy steel content.

ASTM B444 Inconel 625 ERW Pipe has excellent resistance to intergranular corrosion and intergranular stress corrosion cracking, and is mainly used as a heat transfer tube material for steam generators in pressurized water reactor nuclear power plants.

The A420 Grade WPL6 fitting is used in pipelines in the paper and pulp industries, condensers, sea water, marine engineering, waste water management and pollution control systems.

The high strength and corrosion resistance of the AL6XN alloy make it a better choice than the conventional duplex stainless steels and a cost effective alternative to more expensive nickel-base alloys where excellent formability, weldability, strength and corrosion resistance are essential.

Stainless Steel 316L Flange is used to terminate the end of a piping system. The Stainless Steel 316L blind flange is basically a flange that does not have a hub or a bored center. Blind flanges have the face thickness of a flange, a matching face type, and similar bolting pattern. Stainless Steel 316L Blind flanges can also be used to seal a nozzle opening on a pressure vessel.

Too many good properties found in the same product just because of better sheet production. These are high tensile strength, good dimensional accuracy, surface finish, flexibility and durability, withstand heavy loads, strong construction and corrosion resistance. Resistance to corrosion, stress corrosion cracking, crevice corrosion cracking, oxidation/pitting corrosion makes it suitable for a variety of applications.

The Alloy Steel Weld Neck Flange has a welded neck onto it that holds larger pipes in place for easy welding and installation.

ASME SB564 Alloy 601 weld neck flanges Inconel 601 Flanges are made up of a nickel chromium alloy. The material grads range differently with the composition ratio. The 601 grade has 58% nickel, 21% chromium, carbon, manganese, silicon, sulfur, copper and iron in the composition. There are different types such as socket weld flanges, welded neck flanges, Inconel 601 Slip On Flanges, orifice flanges and so on. The flanges made of this material are strong, corrosion resistant to acids, reducing agents and oxidation and are also harder.

We are also shareholders of carbon steel pipe fittings, such as carbon steel butt welding elbows, butt welding carbon steel crosses, butt welding carbon steel tees, butt welding carbon steel end caps, carbon steel butt welding short pipe ends, etc.

Welding Neck Flanges are easy to recognize at the long tapered hub, that goes gradually over to the wall thickness from a pipe or fitting.

The long tapered hub provides an important reinforcement for use in several applications involving high pressure, sub-zero and / or elevated temperatures.

Stainless steel grade 304 is the most commonly used stainless steel. Stainless steel grade 304N has better corrosion resistance than grade 302, and is mostly non-magnetic in nature; however when cold worked it acquires a slightly magnetic quality.

Monel 400 Butt Weld Reducers are resistant to aggressive solvents, acids and bases, and seawater, are highly robust at high temperatures, and are also operable for use in many marine engineering applications.

2507 has good weldability and workability, and it’s widely used in desalination equipment, chemical process pressure vessels, piping and heat exchangers.

2101 is a low nickel, lean duplex stainless steel possessing both superior strength and chloride stress-corrosion cracking resistance when compared to 300 series stainless steel.

310SS flanges also have good resistance to sulfidation and other forms of hot corrosion. Although primarily known for its high temperature properties, 310 stainless steel also provides excellent performance at cryogenic temperatures.

Carbon steel forgings, manufactured in accordance with ASTM A105, are generally used for piping applications. These forged carbon steel piping components (including flanges, fittings, and valves, etc) are used for ambient- and higher-temperature service in pressure systems. The A105N, which is designated with a suffix ¡°N¡±, denotes that the A105 forging shall be furnished in normalized condition. If the forgings are used for piping applications of ASME BPVC or ASME B31, the material shall be its identical equivalent of SA-105 or SA-105N. In short, the heat treatment of normalization distinguishes A105N from A105, or SA-105N from SA-105. ASTM A105 Flange is a specification of flanges. The specification can include different grades of stainless steel material made flanges. The flanges are of forged carbon steel and are meant for high temperature services.

Grade 304 is an austenitic steel with excellent welding and forming properties. These stainless steels are widely used in the petrochemical and food industries for their corrosion resistance, tensile strength and ability to withstand higher temperatures. Depending on the specific grade, there is a compromise between corrosion resistance and temperature characteristics.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.38

ASME SA335 P9 Alloy Steel Seamless Pipe is certified and tested according to Tensile Test, Transverse Tensile Test, Flattening Test, Metal Structure and Etching Test, Photomicrograph, Hardness Test, etc.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.25

The flanges may be made from forgings, castings, or plates covering various types and classes of ASME B16.5 and ASME B16.47 (both Series A and Series B). Stainless steel 304/ 304L flanges of ASME B16.5 are available in Classes 150, 300, 400, 600, 900, 1500, 2500.

U-Bolt medium carbon steel contains 0.3-0.59% carbon, which provides the alloy with increased strength and good wear resistance. It is easy to machine and is used for forging and auto parts. High carbon steel and ultra-high carbon steel are very strong and are used in springs and high strength products. These alloys can be tempered to very high hardness without becoming brittle and are used in very high wear applications. The carbon content of these alloys is 0.6-0.99% high carbon steel and 1.0-2.0% ultra-high carbon steel.

The SS 304 Elbow is one of the key components in the pressure piping system. It basically helps to change the direction of flow in the pipe run. These ASTM A403 Gr WP304 Buttweld Fittings help to connect two pipes with the same or different nominal diameters so as to change the fluid direction by 45 or 90 degrees.

As an ISO certified company, we stand by the principles of quality, safety, and precision in all our products.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

310S and 310H based on the carbon content, are used in high temperature service with high corrosion prone environments because of the high temperature tolerance and high oxidation corrosion resistance.

Alloy 718 is a precipitation hardening nickel-chromium alloy containing large amounts of iron, niobium and molybdenum, and small amounts of aluminum and titanium. It is sometimes called a “super alloy”.

Stainless steel washers are versatile, have excellent corrosion resistance, and have reactive properties when exposed to high temperatures.

A high nickel alloy with the addition of substantial amounts of copper to give the alloy excellent resistance to sodium chloride solutions, including brine and seawater. Therefore, UNS N04400 Alloy 400 Forged Fittings and Socket Weld Elbows can be used as part of an offshore piping system that may require a change of direction.

Incoloy 800H Flange Incoloy 800 / 800H / 800HT Flanges are furnished with nickel-chromium-iron alloys that intend outstanding resistance and strength at harsh environments. The flanges exhibit superior resistance to chloride stress corrosion cracking and crevice corrosion. Even more, it also shows superior intergranular corrosion, stress rupture and creepy aspects. The welding of these flanges is done using various techniques such as MIG, TIG and more.

SMO 254 Flange is Material to F44 Super Austenitic Stainless Steel is described as a 6% Mo Flanges super austenitic stainless.